LG Washer not agitating

LG washing machine WT7200CW only a year and a half old. Within the first 3 months, it started making loud banging sounds when switching from drum spin to agitator spin. Under warranty at that time and the Clutch assembly was replaced by a technician. It has now stopped agitating. I removed the pulsator and the plastic gear is stripped on the agitator. I ordered a new pulsator (AGZ72909702) and the shaft size is incorrect. I then ordered a different part number (AGZ72909701) and same problem...

LG Washer not agitating

via LG Washer not agitating
by VanMann654

Washer control board

It want spin but it will agitate. It has a burnt spot on circuit board in top right corner.

via Washer control board
by THenley

Impeller removal

Customer Problem: Washer would not go into spin cycle. I did run self Diagnostics... when it got to Spin Cycle it wanted to agitate fast, then shut down on overload.
Troubleshot and determined it needed a new Washer Cam Splutch Kit and a new W10528947 Hub Kit.
Problem: I can not get the impeller off, Heated it with a heat gun it still will not come off.
Needless to say after working on it for an hour at the customers residence I consider not to do anymore damage to it and threw in the...

Impeller removal

via Impeller removal
by Willyjay59

Maytag Bravos X MVWX700XL2

Hello,

Was washing clothes yesterday and noticed the timer sticking on 5 minutes. Had to manually stop and put it on rinse and spin to get the water out. I did the diagnostic today and found the code saying excessive time to drain, however, it drains perfect when on the drain and spin program. Did a normal cycle with only water, and once it gets to the spin portion of the cycle at the 13 min remaining, it never kicks in or runs and water. Almost like it skipped the rinse cycle as well. I...

Maytag Bravos X MVWX700XL2

via Maytag Bravos X MVWX700XL2
by Grainwater1122

Maytag Bravos XL

I have a Maytag Bravos XL MVWB835DW0. I stumbled on an error code F7 E8. Can't find info on this or how to run diagnostics test. Does anyone know what this error code is? Machine will not operate.

via Maytag Bravos XL
by Captfriday64

Fisher Paykel WA37T26GW1 washer fault 51 - diverter valve question

Hi All -

I know this is a somewhat uncommon brand (at least here in the US) but I'm hoping someone might be able to offer some assistance on a problem I'm having with my Fisher Paykel WA37T26GW1 washer.

A couple of weeks ago, my washer began stopping about 15 minutes in to the wash cycle. It would beep steadily at one second intervals and display a 00110011 pattern on the "wash progress" lights. My service sheet indicated that this corresponds to a Fault 51 / diverter valve fault code...

Fisher Paykel WA37T26GW1 washer fault 51 - diverter valve question

via Fisher Paykel WA37T26GW1 washer fault 51 - diverter valve question
by rorrer

WFMC1001/UC Bosch - How much water should a washer use for a front loader?

Mine uses about a 1 gallon at startup then a gallon to rinse. I tried this on empty but it timed the same, with cloths or empty. When I try to wash a large blanket the middle is dry. Does the same on hot or cold. Do I have a bad load sensor switch?

via WFMC1001/UC Bosch - How much water should a washer use for a front loader?
by mike Liz

How much water should a washer use for a front loader?

Mine uses about a 1 gallon at startup then a gallon to rinse. I tried this on empty but it timed the same, with cloths or empty. When I try to wash a large blanket the middle is dry. Does the same on hot or cold. Do I have a bad load sensor switch?

via How much water should a washer use for a front loader?
by mike Liz

WFMC1001UC/06 Bosch Washer - Only adds water for about 5 seconds, ( about 1/2 gallon of water) at start up.

Is this normal? Seems ok for the rinse cycle because everything is damp before putting it in the dryer. Sometimes I have to spin it again because its soaking wet. 2006 model.

via WFMC1001UC/06 Bosch Washer - Only adds water for about 5 seconds, ( about 1/2 gallon of water) at start up.
by Mike L

Maytag washer worn splutch?

The other day when doing laundry my girlfriend heard a loud grinding noise during the spin cycle.

I had a look today and it appears that the shaft pulley has worn a ring into the plastic pulley cover. I noticed that the splutch allows some up and down travel of the shaft pulley. However, when I took the splutch apart, nothing looked worn. All the splines appeared solid and the nut holding the shaft pulley was on tight.

I don’t want to throw parts at this thing. What could it be? I...

Maytag washer worn splutch?

via Maytag washer worn splutch?
by Jza

LG SMART INVERTER WASHING MACHINE NOT SPINNING

Hello,
I would greatly appreacite if some experts help to identify the solutions to issue on my LG smart inverter Top washer:
The type of inquiry : Product Operation Product/Model No. : Top Loader/T1366NEFTF Washing machine does not spin and it shows error OE. i have checked from manual that this errors cause due to drainage. I have already checked following but coudl not able to suceeded: Checked and remove the debris from hose and filter tray Checked the drain pump. It is working fine...

LG SMART INVERTER WASHING MACHINE NOT SPINNING

via LG SMART INVERTER WASHING MACHINE NOT SPINNING
by Denis4844

Maytag A806 Service Manual??

I'm looking for a service manual and electrical schematic for a Maytag A806 washer Series 00. This washer is around 41 years old. I've done some looking on the net, with no luck at this point. Does anyone have this manual or a link so I could get it?

Thanks

via Maytag A806 Service Manual??
by MM3971

Bad Bearings Kenmore Elite HE5t Front Loader Model 110.47787800

I have read some great responses from Jake regarding bad bearings for similar machines. I have a question regarding whether the bearings can be changed or if this model requires replacement of tub with bearings. Sears parts states the tub and bearings are one component, however, I have located manufacturers offering bearing kits for my model. If it is possible to replace only bearings, what brand do you recommend? I appreciate you help and want to avoid potential setbacks or inability to...

Bad Bearings Kenmore Elite HE5t Front Loader Model 110.47787800

via Bad Bearings Kenmore Elite HE5t Front Loader Model 110.47787800
by tiffanynunley

Whirlpool Cabrio Platinum WTW8240YW0 Serial # C15070049 Stop at 34 Min.

This is a speed version. Top loader stops with 34 minutes left. LD flashes. No restrictions at pump, filter, or hoses. Will not pump water using manual procedure. Ohm reading at P4 should be 14-18 and it is 19.1 and ohm reading at pump motor is 16.3. Didn’t know if 1 ohm out of range acceptable. Any suggestions on what to do next? I’m thinking motor control assembly. Thanks for any help.

via Whirlpool Cabrio Platinum WTW8240YW0 Serial # C15070049 Stop at 34 Min.
by Vern O.

Westinghouse LA800M washer found almost new

Hi everyone. Long story short, i have a hardly used westinghouse LA800M washer from 1990-1991. I think this model shares a lot of the same parts as frigidaire, so i thought id try my luck. Can anyone offer any insight on this machine? the good, the bad? I believe it to be belt driven. It has been used approx 30-40 times in its life so far and has been sitting rust free. I've attached a pic still showing the manufacturer's label. I'm so thrilled to find a perfectly working NON HE washer that...

Westinghouse LA800M washer found almost new

via Westinghouse LA800M washer found almost new
by Joeyyamaha

Water issues with cabrio

Currently getting error codes F30, f71 and f72 on a cabrio too load washer. When I run the diagnostics the water does not flow to the the detergent, bleach Or softener cups and then gets stuck in C8

via Water issues with cabrio
by Bkelley

Roper RTW4640YQ1 shakes violently

Roper RTW4640YQ1 has started banging like it is unbalanced. I have changed the suspension rods but it still walks the floor. Speaking of floor, it is on a sturdy wooden floor and it is level. I know that some models have tub centering springs and counter balance springs but do not see anything like that on any parts lists/diagrams for my model. Any ideas on what it could be or how to diagnose this issue? Thanks!

via Roper RTW4640YQ1 shakes violently
by radi8u

Admiral Banging during spin cycle

I know this is a common problem but I'm at a loss.
Atw4675yq1 Admiral Clothes Washer
6 years old

I've made sure its level
Replaced suspension rods
Replaced drive block
Don't overfill. Only fill halfway.
Wife wants to buy a new one but I know I can fix this if I can just figure out what is causing it. It get so bad during spin cycle I'm surprised it hasn't tipped over or something. Any help is appreciated. Is there other parts that need to be looked at or tightened?

via Admiral Banging during spin cycle
by Obliv51

what is this code maytag washer

I am having this problem ever since i replaced my washers hub after it got striped out. Now my washer works correctly but at the end of a cycle it will restart by itself all over and run a cycle again. This code pops up after the end of each cycle.

via what is this code maytag washer
by Devondemarco

Lid lock failure please help

I have a GTW500answ0s top load washer. It stopped working so I put in consumer error mode and found out it’s a lid lock failure. I replaced lid lock itself, still nothing. Just replaced lid lock harness and still not working! I have ran the tests and washer will not spin at all. I have also noticed when I run the drain test, it leaks , which never happened before. Washer is not even a year old. Will probably call GE tomorrow, but I would rather fix it myself if possible.

via Lid lock failure please help
by Sarahjane17

MHWE251YG00 won’t start and stay on F1 & E2 codes

I have been working on this washer and replaced the bearings, cleaned everything, It ran for several loads fine but now it’s stopped starting the motor to spin and the water cuts off and then it throws those codes. So, ran a new wire (a mouse appeared to have chewed on it) that goes to the front and rear panels, and then took off the screw again to the rear of the tub, sanded that area and replaced that wire as well. It still won’t work. WTH could be wrong it’s this darn thing?

via MHWE251YG00 won’t start and stay on F1 & E2 codes
by Renata

F3E1 error code Whirlpool Duet

I read a couple of threads on here about this error code problem &the same issues we are having; error code comes on at some point in cycle. If the power button is hit while the machine is in a cycle, the machine will just hum. It does not help to unplug it, when you plug it back in it will start humming again & I cannot open the door even when the machine is unplugged. I read 2 threads where Jake talked about a part (cannot remember the exact name now...something with the word "dome" in...

F3E1 error code Whirlpool Duet

via F3E1 error code Whirlpool Duet
by mwgiedd

Fisher Paykel GW11 won’t power on

I have a Fisher Paykel GW11 that won’t power on. A few months ago the pump started acting up and I knew it was the pump after reading few online post. I thought it was empty of water and tipped it over to get to the pump but it still had some water left in it. Nothing touched the control board and I waited a day of so before I tried starting it but nothing happens now. There is no power going to machine at all, no lights no function no nothing. I read that it could be the control...

Fisher Paykel GW11 won’t power on

via Fisher Paykel GW11 won’t power on
by Rocket Man

Kenmore He2T

Good morning y'all.

I was given a kenmore he2t washer for use with livestock. Not interested in dumping a bunch of money in it. Just wanted to see if you all have any ideas.

Ive got it hooked up and level but its never run water in. Control panel changes setting and start and pause/ cancel works. Lock in the door works. The only thing ive noticed is that the " add a garment" light never goes off and the count down timer never starts. Any thoughts?

via Kenmore He2T
by Joshuamwalker

No agitator dogs? Unbalanced load help

Roper RTW4641BQ1
I appreciate any help greatly!
I have repaired a couple of machines but I'm no expert. This one has me stumped!
Problem is unbalanced sometimes. But there isn't any agitator dogs, or stabalizing spring. The suspension rods look good but I dont see the small springs that are supposed to be at the top of the tub and attached to the stabalizing rods.
Any suggestions?

via No agitator dogs? Unbalanced load help
by Dx2

Belt came off washer

GE, Front Load Washer
Model: GFWS1705H1DG
4 years old

Last 5 minutes of wash cycle (the spin), drum stopped spinning. No weird noises or anything.

Opened the back panel and the drive belt was on the ground.

It keeps slipping off when trying to put back on.

The drive pulley assembly moves in and out too. Tightened the nut and now when I spin the drum with the pulley it makes a “train coming into the station” screeching noise.

Any ideas?

via Belt came off washer
by DIYerJSK

Sears Kenmore Washer Making Weird Noise

We have a Kenmore washer 110.25132410 that just started making a weird noise. File is attached showing the noise. Seems to be running okay currently.

via Sears Kenmore Washer Making Weird Noise
by cmalinowski

Miele washing machine grinding sound

Hi,

While rotating the drum (also manually), there's a strong grinding sound at about 1/4 of a full rotation. 3/4 are completely smooth and 1/4 makes grinding sound like a metal to metal friction.

Any idea what it may be?

attached a short video.

Thank you.

via Miele washing machine grinding sound
by liormolnar

Grinding sound from washing machine

Hi,

While rotating the drum (also manually), there's a strong grinding sound at about 1/4 of a full rotation. 3/4 are completely smooth and 1/4 makes grinding sound like a metal to metal friction.

Any idea what it may be?

attached a short video.

Thank you.

via Grinding sound from washing machine
by liormolnar

How do you fix the Bosch washing machine door error 'no'?

I'm having issues with our Bosch Avantixx 7 washing machine.

After starting a program running about 1 minute the error code 'NO' shows up. Which implies that we're trying to open the wash machine door, which is obviously not true.
I've check the door and can't find any damages or heavy wear whatsoever.
Unfortunately the peep and error keep going continuously without stopping. Which makes it impossible to do laundry.

Any suggestions on how to fix this?

via How do you fix the Bosch washing machine door error 'no'?
by zowika

Whirlpool Washer Spinning Slow

Hey all, new member here, I've got a whirlpool washer (model #LSC9000PW2) that's not spinning fast enough during the extra rinse/spin cycle to drain all the water. What's strange to me is that during a normal wash cycle it will fill, agitate, and spin just fine, draining all the water. But during the next rinse/spin cycle (and optional second/extra rinse) it does not spin fast enough and leaves the clothes sitting in a small pool of water. I'm hoping someone here has encountered this before...

Whirlpool Washer Spinning Slow

via Whirlpool Washer Spinning Slow
by WolfMann

Feedback on Speed Queen Front Loaders

Does anyone know if Speed Queen front load washers DO NOT use the infamous white pot metal spider like the junk Samsung’s ?

The Samsung spider part is made from pot metal that chemically reacts with the aluminum drum and they constantly break.

Does anyone know if the Speed Queen front loaders use steel or other metallurgy that IS NOT susceptible to corrosion ?

Thanks
Dave

via Feedback on Speed Queen Front Loaders
by 65gtotrips

Maytag Atlantis dripping water in tub

There is a slow drip coming from top inside my washing machine when it is not turned on
Serial #20119433ZB

via Maytag Atlantis dripping water in tub
by Flamingo

Whirlpool Duet WFW85HEFW0 won't high speed spin

No error code at all. When in diagnostics it gets to C8 but won't high speed spin. It begins to spin then stops a few seconds later. Initially I received a pump error but I cleaned out the pump and the water drains just fine now. I cleared the error. It still won't spin in high speed . Everything else seems to be working.

Added complete model number

via Whirlpool Duet WFW85HEFW0 won't high speed spin
by Avi worbes

Duet WFW85HE won't high speed spin

No error code at all. When in diagnostics it gets to C8 but won't high speed spin. It begins to spin then stops a few seconds later. Initially I received a pump error but I cleaned out the pump and the water drains just fine now. I cleared the error. It still won't spin in high speed . Everything else seems to be working.

via Duet WFW85HE won't high speed spin
by Avi worbes

Whirlpool error code help!

Our Whirlpool model WFW8540FW1 has recently started showing a F3 E01 error when it starts to go into the first drain and rinse cycle after the wash. I turned it off and waited for the machine to stop sounding like it was draining (it wasn't) and about 5 min later it unlocked the door. Clothes still soaked. I ran the drain/spin setting to get the clothes out but service call is days away.

Been reading about the possibility of Air Dome part being the culprit but need some verification...

Whirlpool error code help!

via Whirlpool error code help!
by Donna R

CAW9244XQ2 Crosley Washer Shifter switch wiring harness

Washing machine started making loud noises during spin cycles (likely due to heavy quilt). Now the washer isn’t spinning or agitating. I followed the tech sheet and ran through things in manual mode. For agitation and spin, the motor hums, but nothing happens. The belt is intact and I followed the test #3a on page 13. Everything checks out until step 9. Between J2-3 and J2-1, the voltage does not switch between spin and agitate modes. What pins should I test for continuity in the shifter...

CAW9244XQ2 Crosley Washer Shifter switch wiring harness

via CAW9244XQ2 Crosley Washer Shifter switch wiring harness
by tmvhx9

Shifter switch wiring harness

Washing machine started making loud noises during spin cycles (likely due to heavy quilt). Now the washer isn’t spinning or agitating. I followed the tech sheet and ran through things in manual mode. For agitation and spin, the motor hums, but nothing happens. The belt is intact and I followed the test #3a on page 13. Everything checks out until step 9. Between J2-3 and J2-1, the voltage does not switch between spin and agitate modes. What pins should I test for continuity in the shifter...

Shifter switch wiring harness

via Shifter switch wiring harness
by tmvhx9

Washer won’t spin heavy knits

My washer works fine on many loads. However when I wash heavy knits, large towels or other very absorbent clothes it doesn’t spin. When the spin cycle starts it immediately goes to spin failure mode and refills and tries to redistribute the load. It then attempts to spin again. On attempting to spin again it immediately goes to spin failure mode again and then shuts down. It never even begins to spin. It then displays the blinking error indicator on the spin light. According to the manual...

Washer won’t spin heavy knits

via Washer won’t spin heavy knits
by Mulh

Whirlpool Duet Sport -- Error Code F33

A few years ago I replaced my drain pump because of error code F33. It's now popped up again and although my impeller seems fine this time I replaced the pump and it did not fix the problem and the error code still pops up. The washer still works on and off without rhyme or reason and will complete a cycle. This has been happening for about 3 weeks now.

There is sometimes a small puddle of water at the front of the washer on the tile. I'm guessing this might have something to do with it...

Whirlpool Duet Sport -- Error Code F33

via Whirlpool Duet Sport -- Error Code F33
by Ezeric

Slow filling washer. All remedies tried.

Hello, very frustrated. Every washer we’ve owned fills slowly. Same house. Just had new one delivered hoping for better but same old slow fill. When you disconnect the fill hoses from unit, water pressure is very good. It’s like the minute it goes into the washer , something causes the pressure to lessen. We have pex water lines with a main baffle. No clogs anywhere. Like I said this is our 4th washer with same result.

via Slow filling washer. All remedies tried.
by cheric2204

Whirlpool Duet front loader stuck in drain cycle

My whirlpool duet front loader wfw8640bw1 is stuck in the drain cycle. Every time we unplug and replug in it sounds like it’s draining. Also, the control panel doesn’t work or light up anymore. When she found it malfunctioning it was making the draining noise and the panel was beeping and flashing a code but she just pressed power and now we don’t know what code it was because the front panel won’t light up anymore. Please help me someone. Thanks
Casey

via Whirlpool Duet front loader stuck in drain cycle
by Wilberc

Whirlpool wtw5300sq0 grease recommendation

Hello fellers,

I have an old Whirlpool wtw5300sq0 washing machine that had worn agitator dogs. I opened it up to install a new agitator kit I bought online. Most online tutorials suggest to use agitator grease which costs 20+ dollars (specifications say that it's simply a high content silicone grease). Will a 3 dollar silicone grease like this one work just fine ...

Whirlpool wtw5300sq0 grease recommendation

via Whirlpool wtw5300sq0 grease recommendation
by DoctorRed

GE washer overloaded & banging on spin cycle. Removed everything, still banging

I overloaded my GE Profile top loader washing machine. It started banging to the point of knocking the front end off. I emptied machine & started spin cycle again. Still banging. "Held, pressed tub backward" & it calmed down. Let go, banging started again. Still empty. Belt seems tight & in tact. What can I look for to possibly repair?

via GE washer overloaded & banging on spin cycle. Removed everything, still banging
by Angelic Mowery

Frigidaire washer FCCW3000FS clicking noise

Hi everyone. Have a Frigidaire commercial grade washer that has been running like a champ for over ten years. Was considering replacing but would like to give a repair a go first. As of the last month, the cycles have not been completing all the way and just this week, standing water ended up in the washer tub and the machine started clicking after a loud thump. I've posted a video.

I know that this model has had a recall due to the water discharge pump being problematic so have contacted...

Frigidaire washer FCCW3000FS clicking noise

via Frigidaire washer FCCW3000FS clicking noise
by Newhomeowner

Frigidaire FCCW3000FS clicking noise

Hi everyone. Have a Frigidaire commercial grade washer that has been running like a champ for over ten years. Was considering replacing but would like to give a repair a go first. As of the last month, the cycles have not been completing all the way and just this week, standing water ended up in the washer tub and the machine started clicking after a loud thump. I've posted a video.

I know that this model has had a recall due to the water discharge pump being problematic so have contacted...

Frigidaire FCCW3000FS clicking noise

via Frigidaire FCCW3000FS clicking noise
by Newhomeowner

Samsung WF365BTBGWRA2 Typical Leak Spots?

Jake:

This is a friend's machine. I will check the obvious such as bad supply lines and drains, but what are the trouble spots on these that make them typically leak? It was made in 2013. I will also ask when it leaks (during fill, during cycle, pumping out, etc).

Thanks.

via Samsung WF365BTBGWRA2 Typical Leak Spots?
by Ponchoguy

Maytag Bravos Washer wont agitate or spin

Just bought a new Bravos Washer. Model MVWX655DW1. Bought it from an outlet, so cant just exchange and got the matching dryer so dont just want to return. Ran a cycle, it went through the whole process, but never once agitated and did not spin at all. Any thoughts? I saw a youtube video that said to calibrate (r,r,r,I,r to get to diagnotic mode, turn to rinse only light then start) but when I tried to do that it just shut off.

via Maytag Bravos Washer wont agitate or spin
by Mogine

My fridgidaire max fill is making this sound???

Speed Queen

Replace drive belt

via Speed Queen
by Mike Bullard

Washer hub

I’m trying to take the hub off of my washer and there is a piece at the top that we have no idea how to remove and it’s stopping us from removing the hub. Any help would be appreciated.

via Washer hub
by David2094

Maytag Bravos XL - Error Code F0 E3

Hello,
Came back from vacation and found that my brother broke my washer. I ran the diagnostic reset and got Error Code F0 E3. Anybody have any idea what's wrong and how to fix it? I still have 3 years left my on my Home Depot xtra warranty but if there is an easy fix, please let me know. Thanks for any help!

Matt C

via Maytag Bravos XL - Error Code F0 E3
by fachauncie

Maytag Bravos - SD Code

6 year old Maytag Bravos top load washing machine.

I've replaced the drain pump, the rotor positioning sensor and I've pulled the wash basket out, no debris in filter or drain hose. Going on day 4 without a washing machine.........help!!!

Clean cycle - runs for ten minutes and throws SD code.....
Normal cycle - starts at 41 minutes, runs normal for 5 minutes, then drops down to three minutes before the SD code appears....

Smells like a hint of burned electronics.....

PLEASE HELP ME!!

via Maytag Bravos - SD Code
by CoachDan

neptune tl fav 6800

I have about completely rebuilt this washer, and being a not so smart pearson, I disassembled the clutch assembly. Everything looks ok, except, I can't remember which one way bearing goes where?
I know they are one way bearings, but I forgot to mark how I removed them from the unit.
Anyone know which bearing goes to the top and which goes to the bottom?
Top counter clockwise? or Bottom?
I know, you don't have to say it "why did I take them out"? LOL
So far-replaced motor control board and...

neptune tl fav 6800

via neptune tl fav 6800
by tbopilot

Washer won’t agitate or spin

Hello my name is Eric,

My washer won’t agitate or spin, It will fill and drain and the timer seems to be working fine.
I took the front panel off, tested the magnetic lid switch and it seems to be functioning properly. The LED light is showing a 6 flash error code. I did the motor reset opening the door and closing 6X it 12 sec. That did reset the motor Error code to normal function but returns to 6 flashes when I run a cycle. I’m thinking the motor is bad but want to see if there is...

Washer won’t agitate or spin

via Washer won’t agitate or spin
by DI-WHY Guy72

GE washer Model GTWN4250DOWS start button not working.

Hi,
My washer is only about 4 yrs old. It has been giving me trouble for about a year now, not starting. I have to repeatedly push the rubber start button to get it going. Well today it will not start at all. Lights are on. I’ve done the suggested reset of the machine and have even taken the front panel off and unplugged/replugged the control board connections to ensure they are all connected well. After reading up on threads here, I think I need a new control board. I appreciate any...

GE washer Model GTWN4250DOWS start button not working.

via GE washer Model GTWN4250DOWS start button not working.
by GinaN

Maytag Neptune won't drain

Hello, I've got an old maytag neptune mah3000aww, the drain pump sometimes works fine, other times won't drain at all. When it doesn't work I can hear a slight electrical hum but pump is not running. If I rotate dial around to spin cycle again , then pump will start and drain normally. Is this a bad pump or something else in control dial?
Thanks

via Maytag Neptune won't drain
by Farmerchad

Inglis Washer Burning rubber smell, can’t locate belt

Hello I have an Inglis by whirlpool washer which I can’t find the model number on, even after tearing it apart, pictures included and I have unbolted the motor which only drops about an inch however I can’t locate the belt nor see any sign of it. But after unbolting the motor and plugging it back in, it seems to spin fine. I can’t seem to figure out this issue

via Inglis Washer Burning rubber smell, can’t locate belt
by Dlippiett

Burning rubber smell, can’t locate belt

Hello I have an Igris by whirlpool washer which I can’t find the model number on, even after tearing it apart, pictures included and I have unbolted the motor which only drops about an inch however I can’t locate the belt nor see any sign of it. But after unbolting the motor and plugging it back in, it seems to spin fine. I can’t seem to figure out this issue

via Burning rubber smell, can’t locate belt
by Dlippiett

Asko W6461 stops mid-cycle, no error displayed.

Hi again,

The same guy who asked me to repair the fridge also has a failed Asko W6461 he bought in 2005. This is a higher-end, horizontal drum machine. According to him, it has suddenly stopped working properly, not completing cycle, but not displaying any error either. Frustrating.

He brought me the relay board, the timer board and the rotary encoder, all extremely expensive parts to replace ($500+ total) as he wanted a second opinion. No part appears burnt, relays have proper contact...

Asko W6461 stops mid-cycle, no error displayed.

via Asko W6461 stops mid-cycle, no error displayed.
by Cubytus

Admiral ATW4675YQ1 Top Loader

Hello,
We have the above named washer and it intermittently skips the agitation part of the rinse cycle. During the wash cycle it fills, agitates, drains and spins properly then, on occasion during the rinse cycle it will fill and then go directly into the final spin mode without agitating.
Has anyone else experienced this? We have noticed it after an electric "burp" in the house where all the clocks have to be reset etc. but not sure if that happens each time as it is intermittent. Any help...

Admiral ATW4675YQ1 Top Loader

via Admiral ATW4675YQ1 Top Loader
by appliancehel123

Washer will not turn on

Hey everyone. The control board will not turn on at all thus not allowing the machine to work at all. I have checked the receptacle and I have 120v. The washer is barely a year old at this point. Has anybody had this issue before?

via Washer will not turn on
by Snuggs07

GE stackable washer no spin

Hello all, I have a ge stackable washer dryer model: GTUP270EM1WW that will start it’s cycle normally then it will agitate for maybe 2 second and stop, if you keep hitting the start button it sometimes will start agitating momentarily then stop again. it will fill/drain normally. I’ve replaced the lid lock assembly with no improvements. I’ve reset the unit and cleared codes.
Please help, thanks

via GE stackable washer no spin
by Dugansbw

Washer want drain. I had a tech come out and put a new pump on it but still want drain

Been working on this for a few days but it’s not getting full voltage at the pump and will not come on I went out in my shop and put for 120 to it and pump came on fine nothing wrong with that it’s in the control panel I’m sure just wondering what I could check

via Washer want drain. I had a tech come out and put a new pump on it but still want drain
by Lloydc123

Samsung WV55M9605MV A5 Washer not starting

Brand New Floor Model. The top washer part works just fine, the main washer does not start. Everything is connected, no error codes, everything is lit up on the panel just fine. The door doesn't really seem to have an lock on it but that seems to be closed tight just fine. Husband has already looked over the main control board and sees nothing weird. Please help!

via Samsung WV55M9605MV A5 Washer not starting
by sweetkkat

Samsung Wv55M9605MV A5

Brand New Floor Model. The top washer part works just fine, the main washer does not start. Everything is connected, no error codes, everything is lit up on the panel just fine. The door doesn't really seem to have an lock on it but that seems to be closed tight just fine. Husband has already looked over the main control board and sees nothing weird. Please help!​

via Samsung Wv55M9605MV A5
by sweetkkat

WF448AAP/XAA Samsung Washer Repair or Substitution of Discontinued Part

This is a Samsung WF448AAP/XAA 02, built December 2009, in service since 2010 when we purchased it new. It has sprung a leak in a T-shaped part (I assume backflow preventer) just before the steam assembly. See here http://bit.ly/2Weq7V3 for context and here for picture of crack in the part http://bit.ly/2WezGTR. This is Samsung part #DC97-12578E, which has unfortunately been discontinued (no luck with Samsung or multiple parts vendors). I have purchased the nearest equivalent (see here http://bit.ly/2WerNhj), but the T off to the drawer is missing what looks to be a smaller second backflow preventer.

Unfortunately, I am a bit uncertain as to the mechanics in play here - specifically, I assume but am not sure the bigger valve is to keep steam from backing into the supply hose (?), but why would the little T off to the detergent drawer need what looks like that other check valve?

My questions... Can I safely use that replacement part as a direct replacement? Can the original part be patched with anything that would hold up to the heat and pressure of steam if that's what its guarding? And finally, if neither of the first two can work, is there any option for disabling/cutting off/rerouting/replacing a broader subassembly to get things going again.

Any help appreciated - definitely out of my depth here and the folks I've asked so far want me to give up on it for lack of the "official" part.

via WF448AAP/XAA Samsung Washer Repair or Substitution of Discontinued Part
by danp110

Whirlpool washer making grinding sound.

Suddenly during a wash load my washer started making a very loud grinding sound. At the time it stopped spinning, but I have since replaced the clutch assembly, drum bushing and motor coupling with no change except that it does spin now. The drum is balanced and there’s no noise when I turn the drum by hand or during the wash cycle. What else can it be? I did notice that the transmission housing is coated with oil although none has dripped on the floor.

via Whirlpool washer making grinding sound.
by DianeH

Amana top load washer only fills on small load, all other load sizes just drain

I did a diagnostic and also a manual reset by unplugging for a minute and opening and closing the lid 6 times in 30 seconds. It used to fill and work on small and medium. I did a diagnostic and large worked again for about 3 loads and now medium doesn't work? ANy advice would be greatly appreciated!!!

via Amana top load washer only fills on small load, all other load sizes just drain
by Wendy Ordway

Samsung Repair or Substitution of Discontinued Part

This is a Samsung WF448AAP/XAA 02, built December 2009, in service since 2010 when we purchased it new. It has sprung a leak in a T-shaped part (I assume backflow preventer) just before the steam assembly. See here http://bit.ly/2Weq7V3 for context and here for picture of crack in the part http://bit.ly/2WezGTR. This is Samsung part #DC97-12578E, which has unfortunately been discontinued (no luck with Samsung or multiple parts vendors). I have purchased the nearest equivalent (see here http://bit.ly/2WerNhj), but the T off to the drawer is missing what looks to be a smaller second backflow preventer.

Unfortunately, I am a bit uncertain as to the mechanics in play here - specifically, I assume but am not sure the bigger valve is to keep steam from backing into the supply hose (?), but why would the little T off to the detergent drawer need what looks like that other check valve?

My questions... Can I safely use that replacement part as a direct replacement? Can the original part be patched with anything that would hold up to the heat and pressure of steam if that's what its guarding? And finally, if neither of the first two can work, is there any option for disabling/cutting off/rerouting/replacing a broader subassembly to get things going again.

Any help appreciated - definitely out of my depth here and the folks I've asked so far want me to give up on it for lack of the "official" part.

via Samsung Repair or Substitution of Discontinued Part
by danp110

WM3170CW LG Washing with LE Error Code

Greetings all!

A couple days ago I received the LE code on my WM3170CW washing machine a few minutes into running a cycle. The drum spins easily in both directions when the power is off. When attempting to run a wash cycle, the motor will try to move but magnetically locks and hums. Occasionally it will spin briefly for about 1/2 of a rotation and make a loud growling sound. Searching the code, it seemed the most likely cause was the hall sensor. I bought a replacement hall sensor (6501KW2002A) from the local appliance parts store and installed it. However, that did not resolve the issue. So, I tested the continuity with a multimeter from the motor and hall sensor connectors to the main board and every pin showed continuity. I physically traced the wires and didn't see any external signs of damage. I tested the resistance of the stator and it showed 10-11 ohms between all three pins. The rotor has all magnets and shows no sign of wear. Considering all this, I bought a used main board. After installing the new board, the issue continued. Any ideas? Replace wire harness? Stator? Rotor? Thanks in advance and any and all assistance!

via WM3170CW LG Washing with LE Error Code
by tburk19

Saga of Samsung washer WA422PRHDWR/AA continues

This is effectively a bump of this thread: Samsung washer model WA422PRHDWR/AA stuck in spin cycle

I wanted to tinker with it a bit more, and I took off the pump assembly, which seemed to be the cause of most of my problems. Sometimes it would drain fine, sometimes not. I thought something might be stuck inside, and I replaced the pump in 2015, so I figured it wasn't the pump.

So, I took the pump off, took the impeller case off and it seems fine, it turns ok and no clogs. So then I hooked up an e-meter to the power inputs to the pump to see if it was receiving power, and I'll be damned if it was. So, it seems like the control board is sending power to the pump as per normal, but the pump doesn't seem to be working.

Thing is, it's a fairly simple A/C motor. power goes in one end, induces a magnetic field that runs the pump. There's not really a lot of things on it that can break. And the impeller turns freely.

Could it be the pump after all? Do pumps go bad after 3 years..........again? I guess I bought the first on in 2012, and replaced it in 2015, and here I am 4 years later, but 4 years for a washer pump that I use twice a weeks seems abysmally poor.

Trick is, the memorial day sales are going to expire next week, and if I can't fix it AND I miss the sale prices on new ones, I'm going to be slightly miffed.

Any thoughts? Just get a new pump?

*Update*

I plugged in the electrical leads halfway onto the prongs on the pump, and hooked up the e-meter to the pump electrical prongs while plugged in, and I couldn't read any electrical potential between the prongs. Then I unplugged the pump motor, and got a solid voltage reading on the power leads from the control board.

Does this mean there is a lack of continuity in the pump, which would mean it is busted?

via Saga of Samsung washer WA422PRHDWR/AA continues
by Barry O'Brien

LG WT1201CW water inlet valve replacement

I purchased a new water inlet valve for this washer, but I can't find any video's specific to this model that show how to open this washer up! Ive attached 2 photos. There are 2 screws that seem to hold the top rear silver cover in place, and 2 screws that hold the rear white portion of the cover (all screw locations indicated by arrows on the second photo). When the screws are removed from the white piece the entire top of the washer wants to life up, but seems to be held in place at the front of the washer. Anyone ever worked on one of these beasts? Could use some advice before I call someone to replace this valve for me.

Attached Thumbnails

   

via LG WT1201CW water inlet valve replacement
by Zummo

Saga of Samsung washer (model # wa422prhdwr/aa ) continues

This is effectively a bump of this thread: https://www.applianceblog.com/mainfo...-in-spin-cycle

I wanted to tinker with it a bit more, and I took off the pump assembly, which seemed to be the cause of most of my problems. Sometimes it would drain fine, sometimes not. I thought something might be stuck inside, and I replaced the pump in 2015, so I figured it wasn't the pump.

So, I took the pump off, took the impeller case off and it seems fine, it turns ok and no clogs. So then I hooked up an e-meter to the power inputs to the pump to see if it was receiving power, and I'll be damned if it was. So, it seems like the control board is sending power to the pump as per normal, but the pump doesn't seem to be working.

Thing is, it's a fairly simple A/C motor. power goes in one end, induces a magnetic field that runs the pump. There's not really a lot of things on it that can break. And the impeller turns freely.

Could it be the pump after all? Do pumps go bad after 3 years..........again? I guess I bought the first on in 2012, and replaced it in 2015, and here I am 4 years later, but 4 years for a washer pump that I use twice a weeks seems abysmally poor.

Trick is, the memorial day sales are going to expire next week, and if I can't fix it AND I miss the sale prices on new ones, I'm going to be slightly miffed.

Any thoughts? Just get a new pump?

*Update*

I plugged in the electrical leads halfway onto the prongs on the pump, and hooked up the e-meter to the pump electrical prongs while plugged in, and I couldn't read any electrical potential between the prongs. Then I unplugged the pump motor, and got a solid voltage reading on the power leads from the control board.

Does this mean there is a lack of continuity in the pump, which would mean it is busted?

via Saga of Samsung washer (model # wa422prhdwr/aa ) continues
by Barry O'Brien

Spin Failure

Eight year old washer won't go into spin cycle. Error code is F7 E1, Basket Speed Sensor Fault. I cleared the codes and rand the Automatic Test Mode and got the same code. I did the Manual Test Mode and tested the low spin, high spin, gentle agitation, and high agitation tests and they all seem to work fine.

The rotor isn't locked, spins freely.

I've removed and reattached the J2 and J16 harness connections from main control to motor and shifter.

I have NOT gotten into TEST #3a: Drive System Shifter.

Which part(s) of TEST #3a will be the most productive for me?

Thanks,
JP

via Spin Failure
by johnpruden

04 Bosch nexxt 500 weird noise on spin

Hello everyone,,
Model number WFMC330SUC/04

hi there, our washer has started to make this odd noise on spin. I took a video of it..it's not a loud thumping, but more of a low pitch screeching. Can send the video if that helps! Tried uploading and it's too large of a file. Thanks

via 04 Bosch nexxt 500 weird noise on spin
by Gabrial

LNC6532A80 Norge Washing machine shaking/vibrating ptretty badly

The machine has worked well for many years. Started shaking badly a week ago. I want to replace suspension rods, snubber ring, anything else? Can I get some help identifying parts? Thank you in advance.

via LNC6532A80 Norge Washing machine shaking/vibrating ptretty badly
by AWSHandy

Norge Washing machine shaking/vibrating ptretty badly

The machine has worked well for many years. Started shaking badly a week ago. I want to replace suspension rods, snubber ring, anything else? Can I get some help identifying parts? Thank you in advance.

via Norge Washing machine shaking/vibrating ptretty badly
by AWSHandy

WF448AAP/XAA Samsung Washer Started Leaking, What part is this?

My Samsung washer (model number WF448AAP/XAA) starting leaking so I opened it and looked at where it was coming from. There is a white plastic part that connects 2 rubber hoses. It looks like it connects to the detergent and bleach reservoir. I notice there is a slight crack in the plastic. I have had this washer for about 7 years. When I do a quick wash (about 41 minutes), it happens at the 8 minute left mark. It doesn't leak water in the beginning of the wash cycle, only towards the end of the cycle when the washer is spinning very fast. Water sprays out for 1 minute or so.

What is the purpose of this part?
What is this part called?
What is the part number?
Where can I order the part from?


I just googled and repairclinic.com or appliancepartspros.com or I can directly call samsung.

I just need to know what this part is called and if there is a way to get the part number somehow. Can anyone help please?

Attached Thumbnails

       

via WF448AAP/XAA Samsung Washer Started Leaking, What part is this?
by irvineboy

What part is this?

My Saumsung washer (model number WF448AAP/XAA) starting leaking so I opened it and looked at where it was coming from. There is a white plastic part that connects 2 rubber hoses. I notice there is a slight crack in the plastic. I have had this washer for about 7 years. When I do a quick wash (about 41 minutes), it happens at the 8 minute left mark. Water sprays out for 1 minute or so.

What is the purpose of this part?
What is this part called?
What is the part number?
Where can I order the part from?


I just googled and found partselect.com or repairclinic.com or can directly call samsung.

I just need to know what this part is called and if there is a way to get the part number somehow. Can anyone help please?

Attached Thumbnails

       

via What part is this?
by irvineboy

Whirlpool Duet top load Washer Error Codes F06 , E01 F08

Purchased new from lows or home depot at lease 6 years ago.

Problem started with the door lock not opening. Now it won't run ie. wont add water.
Ran diagnostic test where you press 3 buttons 3 times within 8 seconds and got the following codes. F06, E01 and F08

Any help would be appreciated.
I'm new on here so hopefully I can somehow find your replies.
Mary

via Whirlpool Duet top load Washer Error Codes F06 , E01 F08
by MaryE

Bosch WFMC3301UC tub filling up with water each night....which part/valve is leaking water?

Hi All,

I have a Bosch Nexxt 500, WFMC3301UC that runs and washes fine, but each night the tub slowly fills with water. I have to run the "drain" mode on the daily manually each morning to clear the tub. The tub is clear after each wash, so i suspect there is some valve that is not closing fully letting my cold water past slowly filling the stainless tub. There are no leaks under the washer that i have noticed. If i turn off the cold water valve at the wall then the tub does not fill overnight (its a slow fill).

Does anybody know which part this might be? Thanks!

parts diagram.
https://www.partselect.com/ModelSect...=Washer&Mark=3

via Bosch WFMC3301UC tub filling up with water each night....which part/valve is leaking water?
by estcstm3

AEG LW1460 Water not heating

Hi there, AEG LW1460.

This washer has only a cold water inlet, and an internal water heater. However, the heating function no longer works. Otherwise all cycles complete normally.

- I opened the washer and tested the 230V 1950W element with an ohmmeter: 25Ω or so.
- The 4.8 kΩ NTC thermistor was an open circuit (infinite resistance).

I ordered the thermistor and installed it today. the new thermistor reads about 8.5 kΩ at a water temperature around 15ºC.

However, the washer is still not heating. The element continues to check out at 25 ohms or so.

One funny thing is that measuring AC voltage between either terminal of the heater element and ground gives me 120V, but voltage between the two element terminals is 0. I find that strange because this is a 230 V unit and the heater is stamped as 230 V as well.

Options:
1. Replace the element (includes another new thermistor) for around $200 CAD.
2. Call in the tech to diagnose properly for around $200 CAD + parts.
3. Any other ideas?

Would be very happy to have your views or any other options.

C

Attached Thumbnails

 

via AEG LW1460 Water not heating
by chenein

LG Washer WM2301HR Won't Start.

I had standing water so I changed the drain pump according to appliancepartspros video.It took me a week because I have a life and later needed a spring spreader. Once everything was finally together it didn't start.

I ensured the plug itself was working. I checked the plug was firmly inserted. And, I checked the circuit breaker. All wires were connected. I also tried a hard reset.

It was working fine up until the standing water and I hadn't started it up again until this point. Now I'm at a loss and hoping someone can help.

via LG Washer WM2301HR Won't Start.
by GEW2019

Samsung washer model WA422PRHDWR/AA stuck in spin cycle

So, my WA422PRHDWR/AA samsung washer has an issue where it just gets stuck in the spin cycle.

There's no abnormal sounds, it drains fine, it just spins and spins and spins. It has an estimated timer on that usually is in the ~15 minute range, but it'll stay there without changing for literally hours. Eventually I just get tired and turn it off manually.

The clothes come out mostly dry, maybe a little more damp than usual.

I've looked into basic troubleshooting, looked at diagnostic and calibration modes, and got a few unbalanced load errors in the diagnostic history. They rarely show up during normal use.

But nothing I can explain why it drains fine, but gets stuck in spin cycle.

My only thought is that the washer cylinder itself seems a bit wobbly. I posted a link to a video of it. Is it normal to have this much room to move the washer cylinder?

If it is not normal, how do I fix that?

https://www.youtube.com/watch?v=yV6uzY3bGBs

via Samsung washer model WA422PRHDWR/AA stuck in spin cycle
by Barry O'Brien

Samsung washer (model # wa422prhdwr/aa ) stuck in spin cycle

So, my wa422prhdwr/aa samsung washer has an issue where it just gets stuck in the spin cycle.

There's no abnormal sounds, it drains fine, it just spins and spins and spins. It has an estimated timer on that usually is in the ~15 minute range, but it'll stay there without changing for literally hours. Eventually I just get tired and turn it off manually.

The clothes come out mostly dry, maybe a little more damp than usual.

I've looked into basic troubleshooting, looked at diagnostic and calibration modes, and got a few unbalanced load errors in the diagnostic history. They rarely show up during normal use.

But nothing I can explain why it drains fine, but gets stuck in spin cycle.

My only thought is that the washer cylinder itself seems a bit wobbly. I posted a link to a video of it. Is it normal to have this much room to move the washer cylinder?

If it is not normal, how do I fix that?

https://www.youtube.com/watch?v=yV6uzY3bGBs

via Samsung washer (model # wa422prhdwr/aa ) stuck in spin cycle
by Barry O'Brien

LG WM2150HW error code TE

Hello;

working on this LG front load washer with a "TE" error. I have measured the thermister at 69 ohms and the heating element measures good. Anyone have any ideas on what i might be looking for on this. Thanks - Gordie

via LG WM2150HW error code TE
by gordiel

LG WT4970CW UE cant solve

Top load washer, probably around 4 years old. It has a 413PN... serial so I believe that's with the newer control boards.

I get the UE code during the rinse cycle. Our older son used the speed wash all the time, and I never noticed him getting the error, but on normal and heavy duty washes the problem has gotten worse and worse, and now I cant get a load done.

I replaced the suspension rods, boom, first load with sheets not and a single problem. Was thrilled, but now it's worse than ever. I checked the stator nut on bottom, its tight. Washers balanced. I checked the water level pressure season tube that it's clear, and it is. I did notice the sensor had a rattle inside of it though.

I ran clean tub mode with nothing in the washer and it went through many cycles of of draining during the rinse cycle. I never pay attention to a normal wash, but it seemed like the pump was trying to drain water for a long time after the tub was already empty. Sign it might be the pressure switch?? It didnt through an error though even though it seem to go through many rinse cycles. I got tired of watching and I think it finally threw the UE in spin cycle.

I'm about to check the drain pump and hoses to make sure they're clear but anyone got any ideas? Maybe the water-level pressure switch, or something else related to UE?

Doesnt seem to be making odd noises

via LG WT4970CW UE cant solve
by Tayloorscott

WJSR4160D5WW Only warm water when hot is selected.

Thanks for allowing me to post!!

I have a GE top loading washer with a water temp selector. I have replaced the hose, the inlet valve and solenoids and the water temp selector switch.
for some reason I only get barely warm water when the hot is selected. Is the cold water solenoid supposed to be open when the hot is selected? if I unplug the cold solenoid I get hot water. Is this normal operation?
Any help would be appreciated!!

via WJSR4160D5WW Only warm water when hot is selected.
by RD427

Only warm water when hot is selected.

Thanks for allowing me to post!!

I have a GE top loading washer with a water temp selector. I have replaced the hose, the inlet valve and solenoids and the water temp selector switch.
for some reason I only get barely warm water when the hot is selected. Is the cold water solenoid supposed to be open when the hot is selected? if I unplug the cold solenoid I get hot water. Is this normal operation?
Any help would be appreciated!!

via Only warm water when hot is selected.
by RD427

Electrolux Front load screen reading wrong time.

I have a Electrolux model number
EIFLS60LT1. Problem with it is after you turn it on the screen shows low minutes for each cycle. Like 37 minutes for normal, 16 minutes for fast wash. All the cycles read less time then what it should be. I tried to reset it but no luck.

via Electrolux Front load screen reading wrong time.
by tseibring

Gorenje w6523 forgot how it works

Dear people of the internet,

I have a weird problem with my Gorenje w6523 front loading washing machine.

I've bought it five years ago and it worked so far without a hitch. However, in the recent weeks it kinda just forgot how the liquids poured into it work. Let me explain that a bit better.

The washing liquid or powder are emptied from the reservoir and can be seen in the tub during the cycle, but the clothes are not cleaned after the cycle. Same goes for detergent / softener, filling the container up with softener would result in an all-enveloping great smell of fresh clothes while drying in the previous years, now nada. No flowery smell, no nothing. It kinda seems to me like the rinse or flush cycles happen prematurely, because judging by the end result the clothes are just spun around in warm water for two hours.
( at least the heating still works just fine )

I've tried the self cleaning program already, and after that the first one or two washes came out smelling just a bit like the softener if you were to smell it vigorously. But after that it's just wet spun clothes again.

There is no bad odour or any of the sorts, the internals look squeaky clean, the water jets above the cleaning solution reservoirs are clean, the reservoirs are clean and liquid can go through them without a problem.

So far I am out of ideas, any input appreciated.

via Gorenje w6523 forgot how it works
by fulee9999

AWNE82SP113TW01 Speed Queen washer basket not turning or "indexing" during wash cycle

Speed Queen top load washer, model #AWNE82SP113TW01 washer basket not turning or "indexing" during wash cycle. The agitator is going back & forth but the wash basket is staying stationary. Any idea what the problem could be?

via AWNE82SP113TW01 Speed Queen washer basket not turning or "indexing" during wash cycle
by Craig Raid

Speed Queen washer

Speed Queen top load washer, model #awne82sp113tw01 washer basket not turning or "indexing" during wash cycle. The agitator is going back & forth but the wash basket is staying stationary. Any idea what the problem could be?

via Speed Queen washer
by Craig Raid

WF395BTPAWR/A unobtainable samsung parts

dc-97-17004a,shaft assembly is no longer supported by Samsung,wonder if anyone has found an exchange part that fits

via WF395BTPAWR/A unobtainable samsung parts
by jim childs

unobtainable samsung parts

dc-97-17004a,shaft assembly is no longer supported by Samsung,wonder if anyone has found an exchange part that fits

via unobtainable samsung parts
by jim childs

New washer making noise

I do not like bein a pain in the a** buyer. At the same time I would hate to repair a brand new washer.

This happened the first time we used it. I have 15 days from delivery to exchange it.

Below is video of the noise. What should I do? Is this an easy repair? Will this be an issue in the futureeven if it is repaired?




Can it matter the dealer I bought it from? Got a really good price. Dryer is also having issues.

via New washer making noise
by jwblue

Seeking suggestion for a new washer

Hi folks,

My current Maytag washer is wearing down. It has a transmission problem that I've been muddling thru (only runs in low gear) and has now sprung a leak leaving a water trail to my basement floor drain. I fear I should replace it, but I'm VERY particular about what I'm looking for and I need some help with that.

#1 -- I DESPISE "High-Efficiency" washers! They are NOT "efficient"! I purchased a Kenmore HE washer once. HATED IT. It sits unused and unrepaired in my basement, and I won't make that mistake again. I want a washer that uses full loads of water -- gallons and gallons of it! I want my clothes CLEAN and RINSED, not damply tossed about to save some carbon footprint somewhere.

#2 -- I want a timer dial, NOT pre-determined wash cycles. I want to be able to stop my load and change the timer. "Oops! I'm running late. I'll shorten this wash cycle and spin it now!"

#3 -- BIG, BIG TUB! My husband is a big, BIG man. His blue jeans are 3x the size of mine. I need to be able to wash more than one pair of his jeans at a time.

#4 -- NO lid locks! My clothes are not convicts! I shouldn't have to break them out of a washer!

#5 -- Extra rinse cycle would be preferred.

Obviously, these are not common features anymore, so I have resorted to purchasing used equipment and running them till they die -- such as my current Maytag washer.

Is there a NEW washer ANYWHERE out there that will not hold my clothing hostage, that I can SEE on the dial how much time has elapsed because it can move and BE moved. Are there still GOOD washers out there that actually freely slosh clothing through gallons and gallons of water???

I was fooled once, but NEVER AGAIN! I had my head turned by a handsome Kenmore washer that CLAIMED to be "High-Efficiency" with a big, big tub, but that was a FARCE! There was NOTHING "efficient" about washing, washing, and rewashing the same urine-soaked bedding or gritty work pants over and over and OVER AGAIN!!!!!!!! I found no joy in having my clothing held hostage for HOURS on end with no indication when the cycle would EVER end! I want an "old-school" washer like my Maytag -- mechanical and reliable, no pansy electronics!

Anyone have a suggestion on how to put a happy ending on this "soap opera"???

Thanks!
~Mavis

via Seeking suggestion for a new washer
by Mavis

WF328AAR/XAA Samsung washer tub won't move

I have a Samsung washer that the drum is locked up and will not turn. The rotor and stater are good and bearings look good.

via WF328AAR/XAA Samsung washer tub won't move
by jefdod

loud noise during the spin cycle

Whirlpool TAWS850PQ0 Estate Washer




Loud noise only happens during the spin cycle

Need help for fixing that loud noise.

Thank you.

via loud noise during the spin cycle
by cznlzq

Samsung washer tub won't move

I have a Samsung washer that the drum is locked up and will not turn. The rotor and stater are good and bearings look good.

via Samsung washer tub won't move
by jefdod

Frigidaire Affinity Cycle Timing Issue

Hello I was wondering if someone could help me, I have a Frigidaire Affinity Washer and recently the wash cycle time would decrease to 3 mins about 2 minutes into the wash cycle. It doesn't make a difference what cycle is selected, if say the normal cycle is 45 mins. in total, at the 43 min. mark it would drop to 3 mins and then then cycle will count down the 3 minutes and finish. During the initial 2 minute period a small amount of water enters the machine and the drum would spin but then it drops to 3 minutes. Has anyone run into this issue? Thanks in advance!

- Tony

via Frigidaire Affinity Cycle Timing Issue
by FrigidaireFFF

Maytag washer making noise during agitation and spin

Mvwc425bw model maytag washer makes a sound that it never made before. It sounds like rubbing noise. Fills, spins, empties fine. The only error cod that comes up is F7E1, which says it's the basket speed sensor. Would that explàin the noise?

via Maytag washer making noise during agitation and spin
by kimmers66@hotmail.com

SAMSUNG WF455ARGSGR te error code

Hey guys,

I've been dealing with an issue on my SAMSUNG WF455ARGSGR washing machine that when it gets to the last 10 mins of a wash cycle, more often than not, it will throw a te code. The only way I've been able to work around this is my powering off the unit, then powering it back on, followed by holding in the spin cycle button for 3 secs and then let it drain several times repeating these steps, which result in the unit sort of completing the last cycle.

One thing I noticed when it's throwing te code, is there's a lot of water in the bed of the washer. We're also not overloading the unit either with clothes - sometimes I've only got 2 sweaters in there, and it'll throw this.

As far as troubleshooting, I've checked all the wires and I've replaced the thermal sensor, but this issue still remains.

It seems that this te code is quite common and I'm hoping someone has an idea on how to fix this.

Thanks in advance for any help.

via SAMSUNG WF455ARGSGR te error code
by karyuudo

Anyone have any advice

I was looking at the thread by Jyn and I have the same issue.
I have the above model Whirlpool Duet washer and the spider has broken.
My machine does list lifetime warranty on the stainless steel drum.

I called Whirlpool today and I guess, because unfortunately I live in Canada and have to deal with the Canadian office they are telling me that because I took unit apart to find cause (not to mention I don’t want to (nor can I afford ) pay exorbitant fees to have appliance tech come out to diagnose my lifetime warranty is now void.
They also say they will NOT supply parts under warranty for me to install because they are concerned about liabilities. But they certainly will sell me the parts to install myself.

The broken spider has caused the front tub to be chewed up and as far as I can see, the rear tub with seal should be replaced also.

Would anyone be able to give me some guidance?

Thank you in advance.

via Anyone have any advice
by Bob 60

Trick for Removing tub springs

I am trying to pull the tub/drum from a samsung BigWash to do a postmortem (there is a grinding sound going on so bad sounding that i am.not even thinking of repair. I'm mostly just curious. Like if.my tenants' child slipped a toy car in there or something)

Is there a trick for Removing the springs the drum hangs from?

Some.videos show a clever system where you can rotate the plastic grommet at the top hook and drop it down.
This setup does not have that.

I expect I need to find a forked tool of some.kind to push down on the lower U hook. But maybe there is a smarter way.

via Trick for Removing tub springs
by pjstock

Whirlpool washer making dark stains on clothes

The whirlpool washer is making dark spots on the clothes, have did vinegar rinses in it but still the dark spots appear on clothing,

just wondering what could be wrong?

via Whirlpool washer making dark stains on clothes
by boudro

Problem after snubber ring replacement Maytag

Hello, I replaced the snubber ring on my Maytag mav208daww everything went fine. After I put it back together the washer will not agitate . It will spin drain but when it try’s to wash/agitate. When it try’s the motor turns on and I can smell the belt slipping and it overloads the motor.
Thanks for the help!!

via Problem after snubber ring replacement Maytag
by Jrs12304

WT5101HV Wash Plate Not Releasing from Drive Shaft Spindle

I have an LG WT5101HV Wave Force Top Loading Washer.

I need to replace the Washer Drive Shaft and Shifter Assembly. To do this I need to remove the Wash Plate and Wash Tub.

I have been following a Repair Clinic Video. The specific spot on the video appears at approximately 1:29 minutes of the 9:13 minute video.



It's a great video and very clear except they are demonstrating on a new washer where every part is easy to remove.

I have removed the Wash Cap and the 10mm bolt / screw securing the Wash Plate. But no matter how I try I can't get the WASH PLATE to release off of the Drive Shaft Spindle.

• I have tried wiggling it from side to side.
• I have placed coat hanger hooks into the 3 alignment holes for the Wash Cap and tried pulling it off.
• I have place a polypropylene rope under and across the bottom of the Wash Plate so as to pull it loose.
• I am pulling in both instances with such force that I can actually lift the Suspension Wash Tub up several inches. I do this in hopes of shaking or breaking the Wash Plate loose.

But still it will not break free.

Any suggestions please on how to release this Plastic Wash Plate?

Thanks

via WT5101HV Wash Plate Not Releasing from Drive Shaft Spindle
by Coleman

AWN432SP111TW01 Speed Queen washer stopped working mid-cycle

I have a Speed Queen washing machine model AWN432SP111TW01, serial 1110013649.

It's been working fine for years and we had never had any trouble with it, but today it stopped mid-cycle, and won't turn back on.

I tested another device in the same electrical socket and it worked fine. I ran an extension cord from an electrical socket in another room which was working fine and connected the washer to it, but still nothing.

I looked in the user guide troubleshooting section under "Won't Start". I have tried everything there. One of the suggestions there is to give it a few minutes for the motor overload protector to reset; I have given it hours.

The user guide does not mention a fuse in the washer.

I opened up the control panel area of the washer and looked for a fuse but did not find one. There was a sheet in there with a schematic. I scoured it for a fuse but it did not mention one.

I looked all over in there for anything that looked burned or otherwise damaged, or loose, etc. Everything looks as good as new and all connections seem tight.

Any suggestions on what I can try?

via AWN432SP111TW01 Speed Queen washer stopped working mid-cycle
by GregL65

Speed Queen washer stopped working mid-cycle

I have a Speed Queen washing machine model AWN432SP111TW01, serial 1110013649.

It's been working fine for years and we had never had any trouble with it, but today it stopped mid-cycle, and won't turn back on.

I tested another device in the same electrical socket and it worked fine. I ran an extension cord from an electrical socket in another room which was working fine and connected the washer to it, but still nothing.

I looked in the user guide troubleshooting section under "Won't Start". I have tried everything there. One of the suggestions there is to give it a few minutes for the motor overload protector to reset; I have given it hours.

The user guide does not mention a fuse in the washer.

I opened up the control panel area of the washer and looked for a fuse but did not find one. There was a sheet in there with a schematic. I scoured it for a fuse but it did not mention one.

I looked all over in there for anything that looked burned or otherwise damaged, or loose, etc. Everything looks as good as new and all connections seem tight.

Any suggestions on what I can try?

via Speed Queen washer stopped working mid-cycle
by GregL65