Maytag A806 Service Manual??

I'm looking for a service manual and electrical schematic for a Maytag A806 washer Series 00. This washer is around 41 years old. I've done some looking on the net, with no luck at this point. Does anyone have this manual or a link so I could get it?

Thanks

via Maytag A806 Service Manual??
by MM3971

Bad Bearings Kenmore Elite HE5t Front Loader Model 110.47787800

I have read some great responses from Jake regarding bad bearings for similar machines. I have a question regarding whether the bearings can be changed or if this model requires replacement of tub with bearings. Sears parts states the tub and bearings are one component, however, I have located manufacturers offering bearing kits for my model. If it is possible to replace only bearings, what brand do you recommend? I appreciate you help and want to avoid potential setbacks or inability to...

Bad Bearings Kenmore Elite HE5t Front Loader Model 110.47787800

via Bad Bearings Kenmore Elite HE5t Front Loader Model 110.47787800
by tiffanynunley

Whirlpool Cabrio Platinum WTW8240YW0 Serial # C15070049 Stop at 34 Min.

This is a speed version. Top loader stops with 34 minutes left. LD flashes. No restrictions at pump, filter, or hoses. Will not pump water using manual procedure. Ohm reading at P4 should be 14-18 and it is 19.1 and ohm reading at pump motor is 16.3. Didn’t know if 1 ohm out of range acceptable. Any suggestions on what to do next? I’m thinking motor control assembly. Thanks for any help.

via Whirlpool Cabrio Platinum WTW8240YW0 Serial # C15070049 Stop at 34 Min.
by Vern O.

Westinghouse LA800M washer found almost new

Hi everyone. Long story short, i have a hardly used westinghouse LA800M washer from 1990-1991. I think this model shares a lot of the same parts as frigidaire, so i thought id try my luck. Can anyone offer any insight on this machine? the good, the bad? I believe it to be belt driven. It has been used approx 30-40 times in its life so far and has been sitting rust free. I've attached a pic still showing the manufacturer's label. I'm so thrilled to find a perfectly working NON HE washer that...

Westinghouse LA800M washer found almost new

via Westinghouse LA800M washer found almost new
by Joeyyamaha

Water issues with cabrio

Currently getting error codes F30, f71 and f72 on a cabrio too load washer. When I run the diagnostics the water does not flow to the the detergent, bleach Or softener cups and then gets stuck in C8

via Water issues with cabrio
by Bkelley

Roper RTW4640YQ1 shakes violently

Roper RTW4640YQ1 has started banging like it is unbalanced. I have changed the suspension rods but it still walks the floor. Speaking of floor, it is on a sturdy wooden floor and it is level. I know that some models have tub centering springs and counter balance springs but do not see anything like that on any parts lists/diagrams for my model. Any ideas on what it could be or how to diagnose this issue? Thanks!

via Roper RTW4640YQ1 shakes violently
by radi8u

Admiral Banging during spin cycle

I know this is a common problem but I'm at a loss.
Atw4675yq1 Admiral Clothes Washer
6 years old

I've made sure its level
Replaced suspension rods
Replaced drive block
Don't overfill. Only fill halfway.
Wife wants to buy a new one but I know I can fix this if I can just figure out what is causing it. It get so bad during spin cycle I'm surprised it hasn't tipped over or something. Any help is appreciated. Is there other parts that need to be looked at or tightened?

via Admiral Banging during spin cycle
by Obliv51

what is this code maytag washer

I am having this problem ever since i replaced my washers hub after it got striped out. Now my washer works correctly but at the end of a cycle it will restart by itself all over and run a cycle again. This code pops up after the end of each cycle.

via what is this code maytag washer
by Devondemarco