GE front loader in cancelled mode and the pump keeps running.

Hello. I have a GE Front loader model GFW550SSNOWW. Somehow it ended up in cancelled mode on screen and the pump keeps running. I have unplugged overnight twice, plugged in, let run for 4 minutes per owners manual and nothing. let run for 20 minutes per a thread. I cleaned out drain hose, tub boot to drain, detergent compartment, inlet filters, strainer, door gasket, etc. i even ran water through it and it pumps. I can not utilize any function on the command pad. Can not really...

Read more

via GE front loader in cancelled mode and the pump keeps running.
by Krl82

Maytag Centennial MVWC200XW2 will not start/ lid lock flashing

I have the washing machine in the title, we bought it about 3 years ago, but it was used. It will light the "sensing" LED, some water will be start running, then the water stops and the "lid locked" light will start blinking. You can hear and feel the lock trying to latch.

At first, I could remove the red cover on the lid lock module (I'm not sure of the correct term) and toggle the rocker back and forth a few times, put it back together and it would run at least one cycle (sometimes 3 or...

Read more

via Maytag Centennial MVWC200XW2 will not start/ lid lock flashing
by LiveWire

F28 error on HE5t

Unplugging and waiting 10-15 minutes doesn't reset it.
I replaced the MCU about 11 years ago. - https://www.applianceblog.com/mainforums/threads/fixed-he5t-just-beeping.23867/#post-119786 which fixed a different issue.
My understanding is that F28 is the CCU, MCU or wiring between the two.
I've done a continuity test of the wiring between the CCU connector and MCU connector and the resistance looks pretty much spot on.

Is there a way to test the CCU and MCU to determine which is bad...

Read more

via F28 error on HE5t
by rover_nut

Maytag mvwb865gw0

I have replaced the door lock, the control panel and power supply and it still does not work.help!!!

via Maytag mvwb865gw0
by sts3717

Kenmore 110.25132410 Agitator Seal

My washer had spinning problems After hours of trying everything, I ended up using a Dremel to cut off the hub, and the metal washplate gear.

With all the abuse, I'm a little concerned about the agitator shaft seal and was hoping to replace it.

If possible, to hold off until after Christmas to get a new washer, so a new gearbox isn't worth it.

Does anyone know if just the seal alone can be replaced, and if so what is it's part number? No part number for my model is shown, since it...

Read more

via Kenmore 110.25132410 Agitator Seal
by ChesterD

Speed queen washer suddenly started making beeping sounds model AWN43RSN115TW01

Out of the blue my speed queen top load suddenly started a random beep. I hear just one beep and it may be awhile before I hear again. I unplugged last night and left unplugged over night. it is 4 mos shy of the 3 yr warranty. i heard it beep and the machine wasn't in use. any idea why? I didn't clean the inlet water filters every 6 months. I will do this tomorrow and call the manu but wanted to see what you think. It is TR3000WN. Other than this strange occurance it washes fine and no...

Read more

via Speed queen washer suddenly started making beeping sounds model AWN43RSN115TW01
by pbhardshell59

Haier HLC1700AXS FD Code First, then DOA (Dead on Arrival)

Hello.

Thought to put out a solution for FD code happened on Haier HLC1700AXS washer combo. Also wanted to ask the community to post here, if known, part numbers of X1 power connectors (both male and female) the GE uses on their boards 0021800040X (original PN) and WH18X27222 (replacement PN). Below is the full story.

My neighbor has a 4 year-old Haier washer combo. All the sudden a month ago the drier stopped heating. It was starting the cycle, but then shortly throwing FD code. The...

Read more

via Haier HLC1700AXS FD Code First, then DOA (Dead on Arrival)
by greenlawn

Speed Queen SWFT71WN trying to troubleshoot.

I have this commercial speed queen frontload washer (SWFT71WN) that stopped working. when you put coins in and press start and then it clicks a few times (like 30 seconds between each one) and then "Close Door" & "Final Rinse Spin" Leds start flashing. The panel has no digital display only knobs, LEDs and a start button. I called this national repair service and got the $69.99 diagnostic service. I tech comes out and tells me it is the door locking mechanism and would cost $370. I told him I...

Read more

via Speed Queen SWFT71WN trying to troubleshoot.
by bleu

Whirlpool tries to spin three times then quits and drains

Washer tries to spin three times then quits and drains​

My whirlpool attempts to start spin cycle several times then gives up and drains. Clicking sound when spins are attempted. Video attached. Drive hub? Belt? Thanks all!

Washer broken.MOV

drive.google.com

via Whirlpool tries to spin three times then quits and drains
by muzteach

Whirlpool Cabrio Drain Pump Continues Running

Good morning, everyone! Long time lurker, first time postern I have a Whirlpool Cabrio Platinum washer WTW8900BC0 approximately 7 or 8 years old. Current issue is that the drain pump intermittently runs continuously at the end of the cycle maybe once every 5th or 6th load. When that happens, sometimes it runs for a few minutes, sometimes it runs for an hour. Nothing I attempt to try seems to fix it when it's stuck. If it's running when I attempt diagnostic mode, it faults at the fill...

Read more

via Whirlpool Cabrio Drain Pump Continues Running
by gijoecam

Asko W6022 fails to load water and exits

The water solenoid does not activate and machine times out. There might be a buzz as well.

via Asko W6022 fails to load water and exits
by laguna_b

Wringer Washer?

Well, the new washers will just not work for me. Can't get pet hair off clothing and sheets even using the dryer. I prefer line drying and it saves electricity. So I am looking at alternatives. Anyone else in this situation? I'm 61 and manually doing laundry will be very difficult for me as I already have back problems. I'd love to find an old wringer washer or some other option. Can those old wringer washers be serviced? Should I just buy a $150 spinner, but still could use...

Read more

via Wringer Washer?
by JMK

Whirlpool Cabrio WTW7000DW0 super load on spin cycle

Hi friends,
I have a problem with our Whirpool Cabrio WTW7000DW0 that is almost 6 years old. The washer appears to work just fine - it cleans the clothes. It does what it's supposed to do.

It's just that it's very loud when it's doing its highest spin cycle. Low and moderate spins aren't overly loud, but when it goes on high spin, it's so loud, you can hear it a floor away even when the door is closed.

It's not uneven at all - just a steady roar. The machine isn't wobbling or...

Read more

via Whirlpool Cabrio WTW7000DW0 super load on spin cycle
by honey_dave

Wife wants a new washer / dryer. But she has a list

So are dryer has been going out for some time but now the washer isn't working. So I have been looking and reading all week on washer dryer sets. I have been all over the place. From top load to front load to the wash tower from lg. So unless i find better info it looks like the ge and lg is the highly rated for mainstream machines. I have some ocd problems and won't be able to pick until i find out who builds the best machines that i can afford. Looking at spending $2300 top. I...

Read more

via Wife wants a new washer / dryer. But she has a list
by ssmokeyy

Whirlpool duet Wfw9150ww00

My whirlpool duet washer runs through till the rinse spin cycle than stops. Remains locked and beeps 3 times every 3 seconds and flashes the wash light

via Whirlpool duet Wfw9150ww00
by chasbrunson

Bosch washing machine, weird noise, trouble spinning

We have a Bosch Nexxt washing machine, I think it's the 500 series. I couldn't find a model number anywhere on it last night but must be somewhere. It's about 12 years old.

Last night, when it was starting a cycle, the water filled and then as it began to spin there was a grinding type noise and the drum only moved a few inches then stopped. I drained and opened it and when moving the drum by hand there was resistance and the same noise but I was able to get it freed up. This happened a...

Read more

via Bosch washing machine, weird noise, trouble spinning
by bcemail

Water issues

Doing laundry with cold water only and do not need the hot water. I've disconnected the hot water hose from the hot water supply and wanting to use only the cold water inlet. when I start the washer, water comes out of the hot water side. Do I need to cap off the hot water inlet?

via Water issues
by pencelarry69

Bosch 300 wisher not spin

My bosch wisher wfvc540 stops spin suddenly, there is not error code in the panel.

via Bosch 300 wisher not spin
by mail8mz

Weak agitation, spins fine Maytag topload

Wash basket and agitator slowly agitate during wash cycle. Spin cycle works as expected.

Replaced the drive motor because I thought weak agitation was the symptom of a weak motor, nope! Tested the capacitor, getting 49uf off a 50uf rating, good there. Removed/inspected belt, splunk

via Weak agitation, spins fine Maytag topload
by madmike12

WTW5000DW1 whirlpool washer Agitation Noise

I am experiencing a noise while my washing machine is agitating. I have already replaced the wash plate, the splutch cam assy, the drive belt, the actuator switch and finally the transmission. Maybe one of the new parts are faulty but I can’t figure out where this sound would be coming from. Right now I am leaning towards getting a different replacement transmission.

I did not replace the motor because the spin function works fine and has no issues.

Any help is much appreciated!

via WTW5000DW1 whirlpool washer Agitation Noise
by Dj64

Whirlpool Gold GSW9559L Ultimate Care™ II, 18 Cycle, Super Capacity Plus Washer

Started a load with it last night and it filled all the way bud will not drain or spin. Now it won’t fill at all either. When I try to turn it on it makes some clicking noises and then stops.

via Whirlpool Gold GSW9559L Ultimate Care™ II, 18 Cycle, Super Capacity Plus Washer
by Caleb_485

HLPW028BXW Haier Top Loader Impeller Screw Broken

I have a Haier washing machine (https://www.haierappliances.com/appliance/2-1-Cu-Ft-Portable-Washer-HLPW028BXW) since about 2017 and for the most part it has been great, we had some coins block the valve that I have had to deal with but nothing major until now. This model doesn't have an upright agitator, just an impeller at the bottom however the screw that holds it in place broke in half so as you can imagine the quality of the wash cycle has diminished greatly. I am having a really...

Read more

via HLPW028BXW Haier Top Loader Impeller Screw Broken
by MFerris

Haier (GE?) HLC1700AXW Washer/Dryer Combo - F9 error

I have an issue with a Haier model HLC1700AXW 24" washer / dryer combo unit, purchased in mid 2020, factory warranty has expired.

My tenants are reporting an F9 Error - Dryer sensor circuit problem. I am told that this error has happened a few times in recent months, and unplugging the machine and plugging in again would clear it. However, now the error is persisting and the machine will not operate.

The owners manual and info online does not offer up anything more than to place a...

Read more

via Haier (GE?) HLC1700AXW Washer/Dryer Combo - F9 error
by SteveH66

Agitator bolt

Hello, I have a whirlpool model WTW5000DW0 lately the bolt that holds the agitator in place comes loose. Every time I wash a load. I have to tighten it up each time. I tried using blue Loctite. But it still comes loose. Any ideas? Thank you.

via Agitator bolt
by EJ60

1 year old hotpoint washer

Hello,

Bought this washer new about a year and 4 months ago.
It started to make this very high pitched noise, but I made sure it’s not overloaded and enough water.

Any help or feedback would be appreciated.

Thanks!

via 1 year old hotpoint washer
by GravityYes

Washer motor won't start on my Kenmore Series 70

Faithful Kenmore Series 70 direct drive washing machine, 22 years old.

Oh I need some encouragement. My washer died mid cycle last week when full of water when it should have started a spin and drain cycle. It was running fine prior, no odd sounds or issues. The motor (I assumed, not up top) was humming pretty loudly and when I got to the washer to inspect I smelled an electrical hot/burning smell. Immediately shut the washer down and unplugged it. Only maybe a minute passed between the...

Read more

via Washer motor won't start on my Kenmore Series 70
by snakeyez

Maytag Centennial leaking

My maytag centennial is leaking into the drum. If it sits, after a few days I have 3" of water and have to run the spin cycle to pump it out. I have to shut off the water supply valve to keep it from leaking. The washer functions well otherwise. I presume it's an internal valve that's worn, what part do I need?

via Maytag Centennial leaking
by pickles4601

Tool/technique needed to balance washer

Hi all,

Thursday we had a new washer delivered and installed (I didn’t do the install and wasn’t able to observe it).

GFW650S*N***

I tried a medium sized load that afternoon, using all the normal/middle-of-the-road settings. During the spin cycle the washer went crazy. Nearly danced itself out of the nook it is in. I paused the machine, redistributed the clothes, started it up, same issue.

Looked at the manual and installation directions. Got out the level and it seems like that’s the...

Read more

via Tool/technique needed to balance washer
by Kmbfixes

Washing Machine Fill Hose

My stainless Fluidmaster fill hoses on my washer are 6yrs old and should be changed. What is a good brand now days to get? I used the 9WM48 length. I didn't use the high efficiency ones and not sure if they are really needed for my top loader? 48" length is fine with straight ends as I don't need the 90deg's. thanks for the advice as there are numerous out there.

via Washing Machine Fill Hose
by cw41

WTW5100HCO F7E7, F7E6, F7E1

Intermittently one or more of these codes will pop up during a wash cycle. Wash does not stop, it progresses on and finishes. I've cleared fault history, sometimes 5 wash cycles no codes. Then 6th wash I'll check fault history after wash is completed and F7E7, F7E6 and F7E1 will pop up. Are these machines famous for broken wires anywhere?
I have factory service manual, just hoping appliance techs might see a pattern of broken wire

via WTW5100HCO F7E7, F7E6, F7E1
by Rkspeed

GE Dishwasher

GE GDT580ssf0ss not heating. It was not filling with water so I replaced the flood switch and now fills however now it does not heat. I checked the heating element with my multimeter and shows 16 ohms. Any suggestions?

via GE Dishwasher
by Nathanholmstrom

Speed Queen washer, code 5, all ligjts flashing

Model AWN43RSN115TW01
All lights flash a 5 code at the end of cycle. Usually can make it operate another load if I reset breaker. Sometimes it will stop right before rinse and lock up with the 5 code. When this happens resetting the breaker might take 2 or 3 attempts before it will rinse and spin out. Twice the lid has remained locked even with power off so I did replace door lock latch. Ran 2 normal cycles after replacement, but then back to locking out at the end of cycle. After...

Read more

via Speed Queen washer, code 5, all ligjts flashing
by Monse

May tag Atlantis makes noise

So my wife said washer makes noise. And close are too wet. I ran a wash came back during spin cycle and u would hear the spin start then this sharp noise and spin would start again to build rpm then the noise eventually it spun but not full speed for any duration. I lifted lid during this and that same noise and drum locked up. Close lid spin starts again repeat with noises. I then noticed it made noise sometimes on agitate too. It's still being used with smaller loads.

via May tag Atlantis makes noise
by Donnny75

Bosch Washer - part 496822 - Rod

Does anyone know what the purpose of the "Rod" part 496822 is on a front loading Bosch Washer. Someone broke it when attempting troubleshooting and I can't figure out what it's purpose is or if it should be replaced. It hangs off of the door latch mechanism with no real purpose . Any help would be appreciated.

Thanks.

​

via Bosch Washer - part 496822 - Rod
by Gam2

Speed queen model awn43rsn115tw01motor bearings replacement

The motor on my speed queen model awn43rsn115tw01 are noisy. I realize that the motor is not designed to be taken apart. What I would like to know is the pulley on the motor threaded and if so left or right.

The motor is a three phase with an inverter

via Speed queen model awn43rsn115tw01motor bearings replacement
by Clydesteve

Samsung Washer Flange Shaft Replacement

Flange Shaft corroded and broke below drum. Ordered 3 different parts with Samsung number. Fits bolt pattern on drum but won't fit shaft. Is this a common problem. Been through 3 different parts companies and backorder. Does anyone have information or a fix?

via Samsung Washer Flange Shaft Replacement
by jnall2

110.92480200 How to take agitator apart to replace Dog Agits?

The Dog Agits part #8800400 on my Kenmore Washer 110.92480200 broke. All the videos I've seen on replacing them (such as this one:

) say to remove the bolt in the middle of the agitator, then the top part of the agitator just pops out.

We took the entire agitator out to replace the lint filter underneath the basket (we removed the entire basket). The agitator came out in one piece. How do we get it apart so we can replace the dog agits? This agitator does not have a...

Read more

via 110.92480200 How to take agitator apart to replace Dog Agits?
by Lizzy

Whirpool HE Top-Load washer WTW5100HW0 F7E1 error

I was able to find online that this error leads to possibly replacing the shift actuator. Ordered and replaced the part, but am still receiving the error code *sometimes*. I've run "drain and spin" cycles, and a "quick" cycle with the washer empty. Previously, the "drain and spin" cycle would look like its going to start, click and hum a few times, then go right to 1 minute left, drain, and ping "washing complete" as if it had gone through everything correctly (but show no error). After...

Read more

via Whirpool HE Top-Load washer WTW5100HW0 F7E1 error
by kwill624

AWN432SP111TW01 Speed Queen washer dead

Speed Queen top load washer quit mid cycle, after fill and wash, start of drain and rinse
Unplugged and restart… dead
Wont respond to any controls, will not fill with more water with change/reset of fill dial, will not agitate, will not spin, will not drain
Checked lid lock switch and ok on ohm meter
Motor spins freely, belt fine
Swapped out mechanical timer (main dial)… still dead

Any suggestions?

Thanks,
Michael

via AWN432SP111TW01 Speed Queen washer dead
by Azmcarroll

Maytag Bravos XL Washer (Code LD - Long Drain)

Maytag Bravos XL Washer (Code LD - Long Drain)

MOD. MVWB850YW0
SER. C13572628
TYPE: 580-05

FYI: Sears Service Warranty completely rebuilt the entire machine... bearings, pumps, electronics, etc.!
Drain Pump motor is humming/spinning (also hearing a "clattering" noise), but not draining. Unplugged power & Turned off water valves!
Removed back cover. Drained remaining water in tub into bucket by lowering hose below tub level.
Tilted machine forward, then used auto jack stand to hold up...

Read more

via Maytag Bravos XL Washer (Code LD - Long Drain)
by Sevysuite

GE top load washer - replaced shaft tube, new shaft squeeks. Normal?

I have a GE top load washer that was sounding like a jet taking off on the spin cycle. Reading here lead me to replace the shaft tube and the tub bearing while I was at it. After installing the new tube it squeaks a lot. The squeak is coming from the bearing in the new shaft not the tub bearing or the belt.

Is this a bad bearing/shaft? Will the squeak fade as it "breaks in"? Can I try lubricating it?

via GE top load washer - replaced shaft tube, new shaft squeeks. Normal?
by Tim K

Whirlpool Washer WTW4800BQ1

This washer started making this noise recently. It is fairly new.

I’m open to ideas of what could be causing this issue.

via Whirlpool Washer WTW4800BQ1
by JimmieJ

Lg washer molex connector

I have a lg wm3700hva that mice chewed the wires off the connector that goes to the module, does anyone know where I can get a replacement end with wire leads? 11 pin connector.

via Lg washer molex connector
by Chadmorgan

Jake, please help!

Hi, sorry to call you out but I've been reading these posts for days and Jake you seem to be the Man!
Anyway, it's the Whirlpool Duet Washer GHW9400PL4 error code FH.
I did the diagnostic test (after disconnecting every hose and filter and wire and cleaning and plugging back in. Nothing was even slightly dirty...although I found a quarter).
And the code happens about a minute into C:01 every time.
According to the manual in the bottom of machine for the technician...

Read more

via Jake, please help!
by thrujenseyes

Whirlpool Cabrio won’t agitate.

My Whirlpool Cabrio won’t agitate. It does everything else fine, but when it starts the agitate cycle it just moves a little, not enough to even make the clothes move at all. And it spins dry perfectly. I checked the wash plate. All the splines look fine. I am trying to look under the drive hub, but it won’t come off. It’s metal, not plastic. I’ve taken the the screws out and it won’t come up. It looks like there is a trick or a tool I need, because it doesn’t seem to be...

Read more

via Whirlpool Cabrio won’t agitate.
by Hankmoon

Maytag washer while cleaning foul odor found rusted agitator shaft

I have taken apart my washer because it has foul odor. While cleaning I found the agitator shaft rusted and poor shape. I cleaned the smell but want to know if I need to replace this part before proceeding? Also what caused it so I can prevent this happening in the future?

via Maytag washer while cleaning foul odor found rusted agitator shaft
by EH57

Maytag Washer YMHWE201YW00 turns on at 1 minute no spin and gets stuck

Hi all,
My washer, model in the title, is permanently stuck at 1 minute, no spin light on. When I run it, it actually gets "Done", but when I turn it on again to try to set up a load, it shows me the same 1 minute and no spin light turned on. See image attached.

I already manually put water in and ran this 1 minute and the pump works fine, therefore, shouldn't be a pump issue. Of course i already tried to unplug the machine for minutes, even hours, but when i plug it back in, the same 1...

Read more

via Maytag Washer YMHWE201YW00 turns on at 1 minute no spin and gets stuck
by nikaum

LWS 11 NW-3062 gearbox service advice and other questions.

Hi,
New to forum, great advice here. Thanks
I looked through the posts, may have missed a thread. 10pm and fatigued...
Busy replacing seals, bearings etc on my washer. Sounded like a jet engine when spinning, grinding when washing. Dud upper seal which leaked onto bearing and thus, failed.
1. Gearbox, should I open up and put fresh lubricant? I cannot source oem, any other options? I have the bronze bush, and 1 small shaft seal. Rest was out of stock at Supplier.
2. Brake pads have about...

Read more

via LWS 11 NW-3062 gearbox service advice and other questions.
by Benji Jones

Frigidaire stackable help

I have a Frigidaire stacked washer/dryer the model number is FEX831FS2. The washer will fill but when it comes time to agitate the motor will just make noise akd eventually start lightly smoking. Local appliance guy came out and installed a used motor he had and same problem. He told me I needed a new transmission. However I was looking at it tonight. The transmission and basket spins very freely by hand pulling the pulley with belt disconnected.

How can I tell if it truly does need a...

Read more

via Frigidaire stackable help
by Robsaun

Water stops then DL error code

The water starts to fill and just stop and we get the code DL code .
I’m thinking lid latch since I don’t hear it engaging .

Any help would be appreciated before I just try the latch assy !

via Water stops then DL error code
by Seanm

ITW4871FW1 Inglis (Whirlpool) Washer Squeak only during fill cycle

Hello!

I have a Inglis (Whirlpool) Model: ITW4871FW1, High Efficiency top load washing machine. During the fill cycle (when the washer is first turned on) it makes an ear piercing squeak as the agitator turns while it fills with water. It does this most times, but not every time the washer is used. For the remainder of the wash cycles, including the second fill cycle, it does not make this sound. I'm stumped as to what is causing it. I know it's not a water pressure issue because we live on...

Read more

via ITW4871FW1 Inglis (Whirlpool) Washer Squeak only during fill cycle
by justiceismini

Whirlpool WTW400BQ1 Makes Grinding Sound

Hello, my Whirlpool WTW400BQ1 top loader washer makes a grinding sound when washing. The machine previously stopped during a wash cycle and would not drain. You could hear it trying (light hum sound) but the sensor would not let it do so. It’s worth noting this was after I had washed a few towels and rugs in sequential back to back heavy loads. I checked the drain pump for clog but found nothing. I performed diagnostic. which resulted in sensor light showing. Attached is a video. Notice the...

Read more

via Whirlpool WTW400BQ1 Makes Grinding Sound
by BobSanders2

Triple action agitator won't move

I have a Kenmore top loading washer Model 11022442511.
The agitator will not move at all. It seems to move along with the drum in the wash cycle not indipendantly. It does not pull clothes up and down.
Also, I hear a rhythmic electronic clicking sound from under the drum. Any ideas on what parts I need to order to repair this?
Thanks!!

via Triple action agitator won't move
by Isaac04

Leak at washer faucet handle

My whirlpool washing machine leaks at the hot water faucet handle when the supply line is connected. When I ran a cycle with the hot water supply line disconnected from the faucet, water came out of the hot water supply hose at high pressure (I drained it into the sink on the washroom). Any recommendations on how to fix this? There is not apparent leak from the faucet when the supply line is disconnected.

via Leak at washer faucet handle
by Mfox518

Maytag MVWB865GC0 Washing Machine Won't Start F2E1

Hey everyone,

I found the forum from this thread with the same exact issue I'm having (https://www.applianceblog.com/mainforums/threads/maytag-washer-mvwb865gc0-wont-start-has-power.84275) and was hoping someone has found the cause of this issue.

The washing machine powers on, but the cycle selector knob will not change to a different cycle, and none of the other buttons are responsive at all.

I've replaced the control board and have a new control panel on the way, but I don't...

Read more

via Maytag MVWB865GC0 Washing Machine Won't Start F2E1
by CPasteur

Whirlpool duet washer not draining

Have a whirlpool duet washer I acquired and have a problem. If I disconnect the internal drain tube from the top near the lid and let it lay out the back it drains perfectly and runs amazing. But if I have the hose connected where it should be the pump won't push the water up vertically and I get an error code. Not sure if I have a week pump or something else happening. Hose is not twisted or pinched when I have it connected. The first picture shows where it connects normally but I have the...

Read more

via Whirlpool duet washer not draining
by manupnorth

GE GUD27 washer leaking water

Washer quit on wash cycle yesterday with blinking wash light. Removed front panel and notice the bottom of washer has water in in. Plus a few socks. Error codes to Blocked Motor but everything spins freely. Cleaned up water, reset the machine, wash cycle again with panel off and noticed steady flow of water water leaking down from the shifter assembly. I'm assuming the drive seal is shot.
Was able to put the washer into Quick Rinse cycle with no water leaking, ran fine right through spin...

Read more

via GE GUD27 washer leaking water
by CrankyFrankE

mvw72332hw0 Maytag will not spin

mvw72332hw0-maytag-washer-will-not-spin-replaced-clutch-and-recalibrated-still-an-issue-would-like-to-confirm-if-main-control-board-is-the-problem.

via mvw72332hw0 Maytag will not spin
by Mkodsu

Old Maytag will not agitate, only spins. Pully turns ONE direction only

Spins fine, NO agitation.

Found washer full of water and not running. Advancing the control to the spin cycle and it spins and drains well. Will not wash (or rinse) because zero agitation.

I took off the belt, and the main pully spins by hand fine ONE direction. Totally locked the other. As in: Totally. Locked.
The pully pops out when turned in the spin direction, which I assume disengages the brake... seems to work (brake works when spin is interrupted by lifting lid.)

Is this a...

Read more

via Old Maytag will not agitate, only spins. Pully turns ONE direction only
by Ryder

Whirlpool Washer (Lsn1000lw0)

Hi there, I have a top-loaded Whirlpool washer that had a drum that wouldn't spin the water out of the clothes. It agitated fine, but the drum just wouldn't do the high or low spin. I bought and installed a new coupler and new clutch assembly (coupler was fine, just wanted to replace since I was removing motor). The clutch assembly replacement fixed the no-spin issue, but now I'm getting a repetitive noise during the spin and the agitation isn't working anymore. The lower agitator (and...

Read more

via Whirlpool Washer (Lsn1000lw0)
by Samps

Discussion: Sealant for spline / threads?

As the saying goes, "an ounce of prevention is worth a pound of cure."

I've just bought a used washing machine (Maytag MVWB765FW3) that had an issue with the door lock latch (F5E1). Electronics being a strong suit of mine I fixed the issue.
But I've now disassembled the machine into its base components for a thorough cleaning. After removing the agitator that was pretty well stuck on the spline, it got me wondering.

Are there any goops or substances I could put on the spline to prevent...

Read more

via Discussion: Sealant for spline / threads?
by BAM5

GTW330ASK2WW loud squeal during agitation only, can manually replicate

Very loud squeal/squeak during agitation only, I can pause the cycle and manually twist agitator a tiny bit and make the sound. Should I remove agitator tower or is it obviously another issue? Thanks for any input.

via GTW330ASK2WW loud squeal during agitation only, can manually replicate
by Estea

FFFW5100PW0 auto temp lights keeps blinking simultaneously

Hi There,

My Frigidaire Affinity washer auto temp lights are blinking without any cause. As soon as i select a program the auto temp lights start to change from temperature (running up and down) This also happens during a washing cycle. what can i do?

Please help

via FFFW5100PW0 auto temp lights keeps blinking simultaneously
by ilonka

Kenmore 970-C98802-00 clicks off and on at beginning of agitation

The washer that came with my condo new, is showing its age, but money is tight. A new combo washer dryer is $2,000. Can’t afford it.

When it starts each agitation cycle, it clicks on and off rapidly for 5 seconds, then it’s fine. It is getting worse. I’ve seen that this can be motor or the close door sensor, but my close door sensor hasn’t functioned since I bought the condo 5 years ago.

Recommendations are greatly appreciated! The dryer also squeaks terribly when it starts, until it...

Read more

via Kenmore 970-C98802-00 clicks off and on at beginning of agitation
by Byro

Maytag stuck on cycling not sensing F6e3

MOD:MW7232HWO
SER: CX2303779
MayTag Commercial Technology
My Maytag washer is stuck on cycle mode and not sensing ? When I run a component activation diagnostic I get a F6E3 error code when I run the unbalance detection I get the F6 E3 error code my, LED light is flashing correctly so I just need to replace the control board ACU

via Maytag stuck on cycling not sensing F6e3
by appzsapp

Kenmore 110.29732800 not draining

Kenmore 700 series top load washer, model number 110.29732800 is not draining properly. The machine does spin and begin to drain but does not finish it, was thinking could be a clogged drain line but haven’t found a video of how to disassemble. Any help is appreciated.

via Kenmore 110.29732800 not draining
by mlj32

GTW460BMK0WW personality code

Hello all.
Ive got new board for this washer ww01f01729 no where to find its personality code.
Please help!

via GTW460BMK0WW personality code
by Toddbutcher

No lights, not working

I have a Maytag Centennial washer and I came home to no lights, not starting. Completely dead. There is power to the outlets. Thank You

via No lights, not working
by JesusFreak

Huebsch Washer TR5104WN

Huebsch 6 cycle 3.2 CUFT,820 RPM Commercial
i bought machine March 1 because i thought a commercial washer would last longer. i live in canada and paid 1800.00. it started making a noise 2 weeks ago on agitation (like a ping pong game being played) Repair man told me today he is replacing gear box. Already? I was told this machine is made by Speed Queen and was an awesome machine. It’s brand new and has not been abused. Is this normal? Anyone ever hear of this? This machine has...

Read more

via Huebsch Washer TR5104WN
by Chris102602

Washer doesn’t spin

Maytag model mhwc7500ywo doesn’t enter spin cycle, except when it does, every few loads. I’ve replaced the door lock and MCB and the machine still only spins sometimes. UDT shows no errors, QDT shows F20, sometimes, which isn’t listed in the service tech doc.
I live in a tropical climate and electrical connections corrode much faster than in N. America so I’m at the point of stripping it down and checking/cleaning contacts.
Any other suggestions?

via Washer doesn’t spin
by Myller

WAT28401UC/17 Bosch Washer 500 Series Power Cord Too Short

I just bought a brand new Bosch 500 Series washer to replace a Bosch Axxis + washer. I have a Bosch Axxis + dryer that still works. The washer is 220V and connects to the dryer using a proprietary plug. The plug is too short to reach the socket in the dryer. I have seen that the Bosch 500 Series dryer is the same, so I would run into exactly the same issue if I purchased a new dryer. I would like to retain the current configuration, rather than purchase a stacking kit.

Preferably, I have...

Read more

via WAT28401UC/17 Bosch Washer 500 Series Power Cord Too Short
by CBenn

Leaks Over Top Of Tub

Working on a LAT2500AAE washer. It leaks water when in the drain cycle over the top of the tub. It seems the force of the spin is making the water run up the sides then over the top. I took the drain belt off and it was worn but not too bad. If I change out the pump and belts will it drain better and then keep this from overflowing the top? Or could there be an issue with the transmission slipping or something that could be a bigger problem? Not sure if I should recommend replacing or...

Read more

via Leaks Over Top Of Tub
by JimmyMas

Speed Queen Loud noise wile agitating.

Loud noise wile agitating.

via Speed Queen Loud noise wile agitating.
by Shaneshelley234

GE Washing Machine turns on by itself

Hi, i am currently having issues with my GTW460ASJ4WW washer. In the middle of the night while we were sleeping, the washer turned itself on. No water was coming into the machine or anything. Just was a buzzing noise. The only way to get it to stop it to unplug it. Any ideas on what it could be before purchasing a new control board? Thanks for any help!

via GE Washing Machine turns on by itself
by CodySmith88

F6E2 error code on Maytag MHW5630hwo

I was washing 2 light blankets when I received a F6E2 error code. I ordered a whole new control panel, but after replacing it the error code was still present. The power button will not work. It will go into diagnostic mode, but not sure what to do after. All connections look fine and I have a green light on one of the other boards (main control?). Not sure what to test or replace at this point.

via F6E2 error code on Maytag MHW5630hwo
by sengra

Lid message on GE GTW755CPM1DG

I have a washer that is displaying the "LID" message and will not start a cycle. What are the possible causes of this?

via Lid message on GE GTW755CPM1DG
by Stcline

Wired loud humming noise samsung DW80k5050UG, rinse cycle only

When dishwasher enters rinse cycle it starts humming loudly. No other modes doing that: washing, draining, water fill, all good, but rinse...
Tried test mode, no errors. Specifically on step 3 of the test mode it inducing that exact looud humming nose, but there is no information anywere what exactly step 3 of the testing doing (
Please help to diagnose what is wrong there.

via Wired loud humming noise samsung DW80k5050UG, rinse cycle only
by pavetro

Speed Queen washer AWN632SP116TW01 excess foam only at drain outlet

Hi,

Seeking help with a problem with a SpeedQueen washer we inherited with a new house.

Washer seems to work fine, but excess foam is generated only at the drain outlet into the wall. The water from the foam seeps out of the outlet receptacle and runs down the wall, where its done minor damage to the dry-wall.

Every web search on this topic shows photos of washers with foam bursting out the top. Not here - we use minimal detergent, and now are using a "low-sudsing" detergent to boot...

Read more

via Speed Queen washer AWN632SP116TW01 excess foam only at drain outlet
by rwmair

Maytag mvwb835dw0 agitation clicking noise

My washer is making clicking noises during agitation; Maytag mvwb835dw0.

via Maytag mvwb835dw0 agitation clicking noise
by Asteigelmann

Top load crosley machine leaking

I have a crosley top load washing machine that leaks water on the large and extra large cycles only any help would be greatly appreciated thanks in advance

via Top load crosley machine leaking
by Thezman1996.zo@

LG TE error code.

I have a wm2501HVA and received a te error code. I purchased a new heating element because my model does not have a separate thermistor available.

After replacing the thermistor it ran successfully for 3 washes then threw the TE error again. I tested the old thermistor and at 200k ohms on a manual ranging multimeter I got .56 (which I think is 56k ohms?) If I drop it down to 20k I get an open line at room temperature (20c).

Is the old part within the correct range and if so how come...

Read more

via LG TE error code.
by Dano123

Maytag=“turns on power, won’t start washing modes nor change modes”

It’s model Maytag MVWB855DC3

Its my Daughters washer so I will probably be doing the work . My son in law is a computer genius but not so mechanical so…..

Can anyone help me to diagnose and repair?

Thanks in advance.

via Maytag=“turns on power, won’t start washing modes nor change modes”
by Checkov

WWRE6260D1WW Agitates but doesn't spin

My washer won't do spin cycle just starts making this loud humming sound.pump seems to work since I can hear water draining .On couple of occasions I was able to start it by hand spinning it right when I heard a click and drum would twitch .the lid sensor works as well,I checked it .cant figure out what is wrong by watching YouTube videos .my washer is about 6-8 years old I believe

via WWRE6260D1WW Agitates but doesn't spin
by KNel

How to diagnose WJRE5500G2WW motor doesn't spin?

Hi,

My GE washer doesn't spin. I reset the motor but still didn't work. How do I know if the motor is bad?

via How to diagnose WJRE5500G2WW motor doesn't spin?
by lgct38

Admiral agitator question

I am asking this question for my uncle. He has a Admiral washing machine model# ATW4675YQ1 and is wondering if the agitator is supposed to work during the rinse cycle? It currently fills, agitator, drains and refills on the wash cycle. On the rinse cycle it fills, drains and spins but doesn't have any agitation.

via Admiral agitator question
by PaulR41

NEW Hotpoint dryer: HTX24EASKWS grinding sound

Year old electric dryer, started with a grinding noise a few weeks back and got worse. Warranty expired in February...of course lol.. I could move the drum with my hand and it still sounded like something grinding. Pulled it apart thinking it was the drum bearing assembly. When drum cover was removed you could see drum was off center. Once drum was completely removed the back had black marks and spots where it was grinding on something. Pulled out bearing assembly and it looks brand new. The...

Read more

via NEW Hotpoint dryer: HTX24EASKWS grinding sound
by Paige19

WTW5000DW1 Washer is not filling with enough water

I have a 6 year old washing machine. It is a WTW5000DW1 by whirlpool. The machine doesnt seem to fill with enough water. Anyone having a similar issues?

via WTW5000DW1 Washer is not filling with enough water
by Chris Vici

Speed Queen/IPSO Washer Problems (Two Machines!)

I have two IPSO coinop machines that need service.

Both are what look to be speed queen designs; almost identical.

The first one makes a terrible noise when in spin cycle. It sounds like a helicopter and it is super loud. The motor and pump turn fine. The helix is ramping off the lower portion and making the noise. There is no spin. I can also turn the intter tub and agitator a few degrees. Is this trans fried?

The other machine is identical and it magically has a wash time of...

Read more

via Speed Queen/IPSO Washer Problems (Two Machines!)
by mountainbiker33

Samsung top load washer WA52M8650AV/A4 won't spin out, shuts down prematurely

Samsung top load washer WA52M8650AV/A4 fills and pumps out but won't spin. Also it shuts down completely after 5 - 10 minutes. Does anyone have a fast track troubleshooting guide or a service manual for this washer?

via Samsung top load washer WA52M8650AV/A4 won't spin out, shuts down prematurely
by dashriprok

What is this sound?

Hey everyone I am new here. Please see the attached video. I took this video of my new Maytag washer mvw7232hw.

I notice the sound when I have a heavy load in. When there is a light load there is no sound and a medium load I will occasionally here it depending on what the medium load consists of. No noise in any other cycle. Is this normal? Or is something wrong?

Btw this washer is brand new and only 2 weeks old. Appreciate any info!

via What is this sound?
by Chase220

GE GUD27ESSMWW washer unit won't drain

I have a GE upright washer/dryer unit that recently is leaving clothes soaking wet after a complete wash cycle.

During the rinse/spin cycle, the rinse and spin LEDs are flashing the entire time. Both rinse and spin LEDs turn solid "On" right at the end of the cycle for a few seconds. The Rinse & Spin flashing LEDs apparently indicate a "Critical Flood", meaning water level is too high. This is interesting since at the end, clothes at the bottom of the washer are soaking wet, but clothes...

Read more

via GE GUD27ESSMWW washer unit won't drain
by RayK

Kenmore oasis 110.28032701 age unknown goes to final drain and spin and uL, even empty. I can’t find anything in a service manual except to rearrange

The washer goes uL even when empty. The service manual only says to rearrange the load. It won’t do the dial spin.

via Kenmore oasis 110.28032701 age unknown goes to final drain and spin and uL, even empty. I can’t find anything in a service manual except to rearrange
by Steve5903

Speed Queen washer AWN432SP111TW01 making a loud banging noise as it starts the spin cycle

My washer is making a loud banging noise as it starts the spin cycle
Almost like something is hitting the side of the cabinet. And it increases as the tub spins faster.

It’s not the drain pump
After cycle is complete
I can grab inner tub and move it slightly

via Speed Queen washer AWN432SP111TW01 making a loud banging noise as it starts the spin cycle
by Wasatchcomm

Speed queen washer AWN432SP111TW01

My washer is making a loud banging noise as it starts the spin cycle
Almost like something is hitting the side of the cabinet. And it increases as the tub spins faster.

It’s not the drain pump
After cycle is complete
I can grab inner tub and move it slightly

via Speed queen washer AWN432SP111TW01
by Wasatchcomm

GE washer Personality

Hello!

Ge Washer, model GTW485BMM0WS

New control board was installed on unit; control did not come with personality profile paper; apon looking up the mini manual, the washer says it needs to be programed to personality 10.

Using step 17 on mini manual I went through the steps of changing the personality.

But with the 6 digit display, the control does not have personality 10....

Personality options are ( with lights off as 0 and on as 1 )

000001
000010
000011
000100
000101
000110...

Read more

via GE washer Personality
by Atapp

GE Spacemaker is Off but partially fills with H2O

GE Spacemaker washer/dryer is Off but partially fills with water by itself at unpredictable times. Model GUD27ESSMWW. Tried rebalancing it. Also checked the screens on the hoses and there’s no debris. Still randomly fills with water 1/4-1/2 way up the tub. Any ideas?

via GE Spacemaker is Off but partially fills with H2O
by Ripleyfrisco

AWN432SP113TW04 Speed Queen Washer generates a very loud noise on spin cycle

Hi,

I have a Speed Queen Washer that generates a very loud noise on spin cycle. The drum appears to spin. This was a sudden issue that has also happened before and just as suddenly resolved. I tried the washer grease trick to no avail.

Here is a short vid of the issue

Thanks

Added model number

via AWN432SP113TW04 Speed Queen Washer generates a very loud noise on spin cycle
by SpeedKing

Speed Queen Washer Issue

Hi,

I have a Speed Queen Washer that generates a very loud noise on spin cycle. This was a sudden issue that has also happened before and just as suddenly resolved. I tried the washer grease trick to no avail.

Here is a short vid of the issue

Thanks

via Speed Queen Washer Issue
by SpeedKing

Fisher & Paykel washer WA37T26GW2 leaking when in recirculation mode

Fisher & Paykel washer WA37T26GW2 leaks water onto the floor only during the recirculation mode. Hoses, pump, main seal ~ the usual suspects, are all dry as a bone. Water from the recirculation hose splashes against the agitator and onto the inside of the cabinet front panel. When in recirculation mode FYI, wash basket is slowly turning at 25 rpm. Recirculation water spews robustly like a garden hose from it's outlet towards the agitator. It's as if recirculation is too vigorous. What...

Read more

via Fisher & Paykel washer WA37T26GW2 leaking when in recirculation mode
by dashriprok

WTW5000DW3 Whirlpool washer , works but grinding noise only during Spin Cycle

Good Evening,
New to the forum, i am having an issue with my whirlpool washer and its only just coming on to 2 years. I have a grinding noise that occurs only during spin cycle. I have checked out the other post on the same model by Paul F, however my noise seems to be coming from under the washer plate and not the circuit board. The noise comes and goes about 20 second at a time.

via WTW5000DW3 Whirlpool washer , works but grinding noise only during Spin Cycle
by Mighty Sweep

Whirlpool WTW8800YC1 SD Error Code

Hello,

My whirlpool washer is giving an SD error code. I have checked for blockage and ran a hot water cycle. At 16 minutes left in the cycle the tub went empty but the drain pump kept running for a long time even after the tub was empty. Finally when the SD error came up the washer started filling with water again and it filled up above half. I then pushed the power button to stop it from filling and it drained out. I felt like it drained out pretty quickly. Everything looks good inside...

Read more

via Whirlpool WTW8800YC1 SD Error Code
by DLMerritt08

Support bad bearjngs and seal

Does support Part# 280184 come with Part# 285203 bearing and seal kit on this washer

via Support bad bearjngs and seal
by Loinest76

Whirlpool WTW4950XW1

Lightly used unit. Was working intermittently. LED is not lit on control board which I'm am leaning toward id a failed control board.
Unit has AC power. Can purchase a rebuilt board for $185 with a lifetime warranty if I return the failed unit to them.
Thoughts?
Thanks

via Whirlpool WTW4950XW1
by Pequod

Maytag Bravos XL MVWB835DW4 F7E5 Error

I have a Maytag Bravos XL washer which is just over 2 years old. I have an F7E5 error code, I have already disassembled and there is nothing under the wash basket. I have also replaced the shift actuator.
Before this repair the machine was stuck between sensing and wash.
Now the machine will sense, wash, rinse but it will not spin and after clearing the codes I still have an F7E5 error code.

Any help in what the next step would be is greatly appreciated.

Thanks,
Candie

via Maytag Bravos XL MVWB835DW4 F7E5 Error
by ck9593

Need a proper sized compact washer/dry combo or stackable

I need a washer / dryer that fits in the space that I have. The dimensions are 28" x 31" x ~84" (W x D x H).
This depth is 31" from the back wall to the door molding on the left side.
There is a PVC pipe in the back that is eating away 2.5" from the depth.

Can anyone please recommend a washer dryer that can fit in this area. Is there a WD combo that is 28" depth?
On the left side if I get rid of the shelfs then that will add 8" tops to the width.

Attached is a pic of the space I have...

Read more

via Need a proper sized compact washer/dry combo or stackable
by 007noob

Kenmore Elite Front Load Washer Leaking Moderately

I bought a washer and dryer matching set from a lady about 4 months ago. She told me she had bought it new then used it for tops 2 years when she then put the set in storage where they remained another 2 years. According to her she was selling them due to a back injury that made the wet clothes too heavy for her to transfer to the dryer. She said when she put them in storage the washer had a small leak that had just started. I can see where some water has ran down the front from up under the...

Read more

via Kenmore Elite Front Load Washer Leaking Moderately
by DawnMarr

Won't run any cycles and shows no codes

Washer will fill slightly then just quit after initial fill. Tried checking for any faults and it shows no codes to be found. What is the issue.

via Won't run any cycles and shows no codes
by Leatherow24

Are Motor control boards 134149220 and wh12x10154 interchangeable.

Thank you all for your time and advice!! From this forum I was able to diagnose that I have a bad Motor Board (Frigidaire part 134149220) In my washer ftf530fs0. I am having a hard time finding one as they are discontinued. I do have a refurbished one on its way for a second time from Canada but imports issues are causing to go back and forth so it a few weeks out. So my question, is GE part wh12x10154 interchangeable with my my board? They look identical and the GE part is way easier to...

Read more

via Are Motor control boards 134149220 and wh12x10154 interchangeable.
by michaelcavis

Speed Queen Washer noise during rinse spin cycle

Have a 4 yr old Speed Queen AWN63R still under warranty but looking like its gonna be a hassle to get a tech out under this Biden economy. Will probably dig into myself. Getting a thumping noise during high speed rinse cycle...doesn't seem to do it without clothes. Not unbalanced, bearings seem fine when I spin agitator by hand. Thinking maybe Idler pulley? Hopefully the video uploaded OK...was having issues

via Speed Queen Washer noise during rinse spin cycle
by jmer817

Speed Queen Washer Won't Fill and Won't Stop Running

Model AWN432SP113TW04 just keeps on running with no water. Pull knob and it goes from one cycle to next cycle to next cycle...round and round. AND, no water runs in the tub.

I'm thinking timer. What do you think or what diagnosis path do you suggest. Plenty of water going to the washer.

via Speed Queen Washer Won't Fill and Won't Stop Running
by gebo

Frigidaire combo model number FEX831CS0

Can someone help please, I have a frigidaire combo model number FEX831cs0 the washer won't start filling with water until I press the DRYER start button, when I release the button it stops filling with water. When I put the washer on spin it dose nothing until I press the dryer start button then the dryer starts and the washer spins

via Frigidaire combo model number FEX831CS0
by ironroad75

Electrolux Washing Machine EFLW417SIW0

My front load washing machine has a small puddle on the ground right in front/under the door after every load.

I have inspected the seal around the door and it is in good condition. I also recently replaced the door latch and door locking mechanism and this did not change/improve the problem.

Other thoughts or suggestions?

via Electrolux Washing Machine EFLW417SIW0
by mjschmid