Maytag Washer won’t run.

We have a used MVW6230HW0 that won’t run. It tries to start and half spins 3-4 times then the timer drops to to 0:01, the drain pump runs and then it says cycle complete. Video for reference. Any tips to resolve?

via Maytag Washer won’t run.
by HoldTheMustard2

GE washer stuck on very last spin cycle

Hi there! New to the forum here! So I work for a maintenance property complex and we are starting to get these new washers in that are digital. So a little different than the mechanical timers that we are used to. So trying to learn all the new washers. Long story short our new washer is stuck on the very last cycle the spin cycle. So before when a timer gets stuck we would just replace. So we got a new control board and replaced it. Same issue!? So did some research and everything leading...

Read more

via GE washer stuck on very last spin cycle
by Anthonylh

AWN632SP116TW01 Speed queen washer under water

speed queen AWN632SP116TW01 was under about 1 ft of water when our basement flooded. Out of warranty. Was under for about 4-5 hours. Doesn't light up anything or start. Taking it apart i found the lower control output board is bad. I work in electronics all day so familiar with components. There is a large diode that is blown in 2 pieces and maybe a few other components i would say look iffy. Motor appears ok, no rust and turns freely, i had a fan blowing on it for a few hours once we got...

Read more

via AWN632SP116TW01 Speed queen washer under water
by mozzman

AWN632 Speed queen washer under water

speed queen AWN632 was under about 1 ft of water when our basement flooded. Out of warranty. Was under for about 4-5 hours. Doesn't light up anything or start. Taking it apart i found the lower control output board is bad. I work in electronics all day so familiar with components. There is a large diode that is blown in 2 pieces and maybe a few other components i would say look iffy. Motor appears ok, no rust and turns freely, i had a fan blowing on it for a few hours once we got the water...

Read more

via AWN632 Speed queen washer under water
by mozzman

Speed queen under water

speed queen awn632 was under about 1 ft of water when our basement flooded. Out of warranty. Was under for about 4-5 hours. Doesn't light up anything or start. Taking it apart i found the lower control output board is bad. I work in electronics all day so familiar with components. There is a large diode that is blown in 2 pieces and maybe a few other components i would say look iffy. Motor appears ok, no rust and turns freely, i had a fan blowing on it for a few hours once we got the water...

Read more

via Speed queen under water
by mozzman

maytag washer Mvmc416fw bearing?

We just bought a new home. The washer is making a super loud noise during spin cycle. Would this likely be a bearing?

Would this possibly be a user-fixable issue?



Thanks!

via maytag washer Mvmc416fw bearing?
by Debbie K

Ge washer making horrible noise

Please help!

via Ge washer making horrible noise
by Ryanboyd

Overheating Maytag washer

My older May tag washer, model number lat9334aae, motor overheats. But not when I disconnect the main drive belt.

via Overheating Maytag washer
by Lwburger

Speed Queen Washer HA7221 Leak Advice

Hi folks, looking for some advice for my old Speed Queen HA7221. The washer has had an intermittent leak from the bottom for maybe a year now. It was only happening with heavy loads so we were just keeping them smaller. Now it has started squealing during spin and is leaking pretty consistently. I took the front cover off today and it helpfully shot some water into my face during spin, so I was able to locate the leak. It looks to be coming from the main bearing (see photo, location of water...

Read more

via Speed Queen Washer HA7221 Leak Advice
by capecod41

Speed Queen HA7221 Leak Advice

Hi folks, looking for some advice for my old Speed Queen HA7221. The washer has had an intermittent leak from the bottom for maybe a year now. It was only happening with heavy loads so we were just keeping them smaller. Now it has started squealing during spin and is leaking pretty consistently. I took the front cover off today and it helpfully shot some water into my face during spin, so I was able to locate the leak. It looks to be coming from the main bearing (see photo, location of water...

Read more

via Speed Queen HA7221 Leak Advice
by capecod41

TR3000WN Speed Queen Washer Question

I have a SQ TR3000WN. Is there a diagnostic mode or anything for this machine? I found online how we can force a rinse and spin but I was hoping there was a way to do a manual test or confirm if there is a calibration.

via TR3000WN Speed Queen Washer Question
by mountainbiker33

Speed Queen Question

I have a SQ TR3000WN. Is there a diagnostic mode or anything for this machine? I found online how we can force a rinse and spin but I was hoping there was a way to do a manual test or confirm if there is a calibration.

via Speed Queen Question
by mountainbiker33