Brand new LG washer dripping water from boot/gasket valve.

I just received my brand new hours old LG washer. I noticed after the washer is done and I open the door that it is dripping a lot of water from this orange valve that’s on top of the boot/gasket. I wipe the seal and that valve, but it drips off and on.

I’ve never had a washer have this valve on the upper gasket. Did I get a defective machine, or is this dripping normal? I don’t want to have to go back and repeatedly wipe it up from time to time, not to mention any standing water could cause mold growth over time.

Attached Thumbnails

 

via Brand new LG washer dripping water from boot/gasket valve.
by Jarmenta

Speed Queen Top Loader Tub Seal Replacement

I don't have this problem yet, but I'm reading about the dreaded tub seal replacement and would like to have the tools available just in case (and I could use a set of gear pullers).

Speed Queen uses an agitator drive bell (39508P)

http://ift.tt/2fGkYGb

that requires a special tool (294P4 or TJ294P4). The 294P4 is about $82:

http://ift.tt/2fFvwoX

I'm wondering if a generic gear puller would be adequate to replace the drive bell? If so, would a 6" or 4" be better. Here's the gear puller kit I'm thinking about, but I'm also open to recommendations:

http://ift.tt/2eg9Avu

via Speed Queen Top Loader Tub Seal Replacement
by giants1

Top Load Kenmore Elite leaking- cannot find source

This machine is made by LG. So far, have not found more information on this model leaking. I took off the back panel and ran a rinse/spin cycle. Some droplets of water were leaking down the side of the outer plastic housing surrounding the drum. During the entire cycle...no water leaked from the drain pump, tub to pump hose, or drain hose. More water leaks during the wash cycle. It does not leak ALL the time, maybe only 80%. My guess is water inlet valve assembly. Any info regarding experience with this issue would be much appreciated.

via Top Load Kenmore Elite leaking- cannot find source
by AWSHandy

Maytag Bravos MCT washer stopped working and can't activate diagnostic test modes

I have a 2015 Maytag Bravos MCT Washer that stopped during rinse and drain cycle with a amber flashing sensing light. I held start button for three seconds and light goes off and then unplugged for a minute and plugged back in. Amber sensing light comes on flashing but can't get any cycles to work. Tried accessing Service diagnostic test modes via service tech instructions but can't access. Any suggestions on why I can't access diagnostic modes?
Thanks much!

via Maytag Bravos MCT washer stopped working and can't activate diagnostic test modes
by brine

WM1812CW Fixed the Bearings & Seals- Did I fix the wrong thing or mess something up?

I have an LG WM1812CW washing machine. It started doing a weird spinning that sounded like a jet plane. Then it started making horrible noises. So, I just replaced both bearings, seal and tub gasket. The bearings were terrible. Put it back together and tested it spinning manually and then continued. However, we never checked after we reinstalled the stator assembly and cover. There was a crack in one of the magnets but everything looked ok except a fair amount of rust color which seems like it’s not uncommon looking at some videos. Is it possible we didn’t install the stator properly or too tightly, etc…Or could that little crack matter? So, we plugged it in and now it makes a sound when spinning almost like it’s hitting something or catching on something.

We pulled the top off and spun it manually and as stated above, it sounds and feels like the metal tub is catching something. Could the problem be the stator or the rotor assembly? Did I fix the wrong thing?

Any thoughts?

I appreciate the help!

Also, this is the video I used to repair

via WM1812CW Fixed the Bearings & Seals- Did I fix the wrong thing or mess something up?
by funkyone

Bosch WVG30461GB won't lock and start

Hello,

It is my first post here, and I hope I will find some help about this matter.

I have this washing machine Bosch WVG30461GB, which started acting up a while back. So I'd click on the start button, after having selected the program, the door would click once and then click again, the machine would beep twice, the lock icon won't come on and the machine won't start.

It used to be intermittent, and in the instances where it didn't start, retrying a few times usually got it working again.

About a week ago the issue became permanent, no matter how much I retry the issue persists.

After having checked the obvious things, including no blockages or anything stuck in the pump. I looked a lot on the internet, and it seems most answers pointed towards the interlock being the faulty part, I took it out, bought a new one and installed it, but nothing changed the issue is still the exact same.

An additional thing I did actually try, is I took the old interlock, opened it, removed the locking mechanism from it (the mechanical tongue that locks the door), and then I forced the solenoid in the locked position, low and behold the machine starts, most of the time, sometimes it still doesn't but retrying a couple of times usually works. obviously this is not very safe as the door can be opened at any time.

The last test I did is I started disconnecting the different parts of the machine one by one thinking that if there was a short circuit somewhere this might help me find it, but none of this helped, every time I disconnected something and tried it did the same exact thing. except a couple sensors that when disconnected didn't allow me to click the start button in the first place.

So here I am super confused about what the issue might be. Sorry about the long post, but I thought the more information I give the better you would be able to diagnose and hopefully shed some light on what might be going on.

I thank you all in advance.

Regards.

via Bosch WVG30461GB won't lock and start
by jake1985

Kenmore compact washer vibrates during spin cycle

Load is balanced and washer is level, but it vibrates a lot during spin cycle.

via Kenmore compact washer vibrates during spin cycle
by giants1

Fixed the Bearings & Seals- Did I fix the wrong thing or mess something up?

I have an LG WM1812CW washing machine. It started doing a weird spinning that sounded like a jet plane. Then it started making horrible noises. So, I just replaced both bearings, seal and tub gasket. The bearings were terrible. Put it back together and tested it spinning manually and then continued. However, we never checked after we reinstalled the stator assembly and cover. There was a crack in one of the magnets but everything looked ok except a fair amount of rust color which seems like it’s not uncommon looking at some videos. Is it possible we didn’t install the stator properly or too tightly, etc…Or could that little crack matter? So, we plugged it in and now it makes a sound when spinning almost like it’s hitting something or catching on something.

We pulled the top off and spun it manually and as stated above, it sounds and feels like the metal tub is catching something. Could the problem be the stator or the rotor assembly? Did I fix the wrong thing?

Any thoughts?

I appreciate the help!

Also, this is the video I used to repair
https://www.youtube.com/watch?v=WY7KQMcsWKY

via Fixed the Bearings & Seals- Did I fix the wrong thing or mess something up?
by funkyone

Kenmore Top Loading High Efficiency Washer

The lid lock light was blinking and the washer would not work. I figured out how to run a diagnostic on it as well as what the diagnostic determined the issue to be. Long story short...I changed the actuator. The washer then worked and the wash cycle completes and shuts off normally. Then a few minutes later it turns on automatically without me touching the cancel/start/pause button. i have even tried unplugging for a few minutes and plugging it back in...but once its plugged back in it starts a cycle again without pressing start. Also, I laid the washer on its front belly to access underneath where the actuator is installed...and ever since I replaced the actuator... not only does it continuously turn on but during spin cycle it is so loud it sounds like an airplane taking off.

Thank you for any guidance...

via Kenmore Top Loading High Efficiency Washer
by tcsolid

WF407ANW/XAA Samsung Front Load Washer does not Spin with clothes in it

I am working on a Samsung front load washer model no. WF407ANW/XAA. Washer is not spinning when loaded with clothing. When I run the washer by itself it completes a cycle correctly. Washer does rinse correctly. Washer does not give me an error code.

via WF407ANW/XAA Samsung Front Load Washer does not Spin with clothes in it
by omargzj

Samsung Front Load Washer does not Spin with clothes in it

I am working on a Samsung front load washer model no. WF407ANW/XAA. Washer is not spinning when loaded with clothing. When I run the washer by itself it completes a cycle correctly. Washer does rinse correctly. Washer does not five me an error code.

via Samsung Front Load Washer does not Spin with clothes in it
by omargzj

FIXED WFMC3301UC/06 Bosch Nexxt 500 Series Washer leaking

My Bosch Nexxt 500 Series front loading washer just started leaking yesterday. It is a pretty fast leak, too. I know it is not the drain pump as I took the cover off the drain pump and shined a flashlight under the washer. The best way to describe where the leak is coming from is approximately 8-10 inches from the left and 6 - 8 inches from the back. I put it on the drain and spin cycle and saw it leaking maybe 1 drip every 4 to 6 seconds.

Is this repairable without parts (kind of doubt this) or what parts are probably needed and what is the price? The washer is 10 years old and I've already spent about $125 to repair it (drain pump and cold water inlet valve), so if the price of the part is prohibitive, I might just opt for a new washer as I have $200 in Lowe's gift cards. I did see a Maytag and Whirlpool front loading washer there for $719 (4.5 gallon capacity), which is less than I paid for the Bosch 10 years ago. I might opt for another Bosch, but nothing but 2.5 gallon washers there right now, which is too small for our family.

via FIXED WFMC3301UC/06 Bosch Nexxt 500 Series Washer leaking
by neustkg

WF337AAW/XAA Solenoid controlled shutoff valves need to be redesigned

Other than needing to unplug and plug the power cord back in to reset a fault a few times, we have had no major problems (knock on wood) with our Samsung washer. One major annoyance has always been the LOUD Solenoid banging when the shut-off valves open or close. Our water hammer arresters finally bit the dust and we replaced both. The water hammer noise from the pipes was solved but not the solenoid noise. Why can't they design a soft open/close valve system that does not make noise or create a water hammer condition ? It shouldn't be rocket science if you ask me. Our laundry room is on the second floor of our house where our bedroom is. The noise from the solenoids is loud enough to wake the dead.

via WF337AAW/XAA Solenoid controlled shutoff valves need to be redesigned
by Glenn Watkins

Bosch Nexxt 500 Series Washer leaking

My Bosch Nexxt 500 Series front loading washer just started leaking yesterday. It is a pretty fast leak, too. I know it is not the drain pump as I took the cover off the drain pump and shined a flashlight under the washer. The best way to describe where the leak is coming from is approximately 8-10 inches from the left and 6 - 8 inches from the back. I put it on the drain and spin cycle and saw it leaking maybe 1 drip every 4 to 6 seconds.

Is this repairable without parts (kind of doubt this) or what parts are probably needed and what is the price? The washer is 10 years old and I've already spent about $125 to repair it (drain pump and cold water inlet valve), so if the price of the part is prohibitive, I might just opt for a new washer as I have $200 in Lowe's gift cards. I did see a Maytag and Whirlpool front loading washer there for $719 (4.5 gallon capacity), which is less than I paid for the Bosch 10 years ago. I might opt for another Bosch, but nothing but 2.5 gallon washers there right now, which is too small for our family.

via Bosch Nexxt 500 Series Washer leaking
by neustkg

Solenoid controlled shutoff valves need to be redesigned

Other than needing to unplug and plug the power cord back in to reset a fault a few times, we have had no major problems (knock on wood) with our Samsung washer. One major annoyance has always been the LOUD Solenoid banging when the shut-off valves open or close. Our water hammer arresters finally bit the dust and we replaced both. The water hammer noise from the pipes was solved but not the solenoid noise. Why can't they design a soft open/close valve system that does not make noise or create a water hammer condition ? It shouldn't be rocket science if you ask me. Our laundry room is on the second floor of our house where our bedroom is. The noise from the solenoids is loud enough to wake the dead.

via Solenoid controlled shutoff valves need to be redesigned
by Glenn Watkins

Unable to Separate Top Half of Agitator from Bottom Half

The top of the agitator spins freely CW and CCW. I removed the 7/16" bolt easily, but I cannot separate the top from the bottom. I see a rubber washer still in the center of the shaft. When the bolt was in place, it surrounded it.

The agitator assembly spins with the lower half of the agitator.

I can clearly see that the agitator dogs are worn and need to be replaced, but the top is too deep for me to use my hand or a tool to pull out the agitator dog assembly.

Please help. Thanks!

Attached Thumbnails

   

via Unable to Separate Top Half of Agitator from Bottom Half
by giants1

Agitator/Washplate won't spin during wash cycle.

Within the past two weeks we have been experiencing problems with our Maytag Bravo top load washer. Usually the agitator/wash plate will move during the Sensing cycle and then of course during the Wash cycle. Unfortunately this is not happening so the clothes appear to just sit there during the Wash cycle. However the agitator/wash plate will later move as it should during the Spin cycle, but sounds not right. I have attempted to do a wash without anything in it and of course the agitator/wash plate works as it should during all cycles but it is spinning at warped speed (not sure if that's because it's empty or what). It's like a full load of clothes is preventing it somehow. Of course that's not the only issue, when it's all done, the clothes are still very wet to the point they need to be hand wrung to get the excess water out. I have attempted to remove the wash plate with no luck. I was able to remove the center cap on the wash plate that protects the bolt, and then was able to remove the bolt, the issue is actually getting the wash plate up. It acts stuck like there is something else holding it down, but according to some YouTube videos I saw it should be able to lift right up. I want to see what is going on under the wash plate to see if something (fabric, string, etc) is keeping it from spinning as it should during the Sensing and Wash cycle. I feel like this is an easy fix and was given a quote of $100 just for a service repairman to just walk in our door, not even touch the washer. Any help would be greatly appreciated. I don't want to have to buy a brand new washer after not even owning this one for 2 years.

via Agitator/Washplate won't spin during wash cycle.
by jengreen

Frigidaire Stackable Not Agitating

Center agitator won't move during wash cycle however spins freely by hand. Belt appears to be moving the transmission because tub will spin during spin cycle.

via Frigidaire Stackable Not Agitating
by Disp122

Fridgidaire Affinity E5E error

Hi,

I've been having some problems with my fridgidaire washer. The water fills very little then just stops, or sometimes just doesn't do anything when I start the washer. I tried finding the error code and I get the E5E error code, which I think means communication error when I checked. Is there any chance that this is cause by a clogged trap? There is no front panel, I think I'll have to unscrew the top part first and go from there to check the trap. unfortunately our builder stacked the dryer on top of the washer. I'm guessing there's no easy way to get it down. Thanks.

via Fridgidaire Affinity E5E error
by ramyun

Wiring Diagram for Whirlpool Top Loader?

Whirlpool refuses to send me the wiring diagram, saying they give it only to techs.

Anyone have a link to the wiring diagram for

LSQ9550PW3

Thanks

via Wiring Diagram for Whirlpool Top Loader?
by giants1

Samsung Front Loader Leaking - Worth Repairing?

Samsung WF210 ANW/XAA, high efficiency, 3.5 gal, 5 years old (bought Feb 2012), used less than twice monthly and not abused. For the past month, it has a small leak (30 cc?) coming from the left rear. I have concrete floors sloping to a drain, meaning about three feet of water exposure, so damage to the floor is not an issue.

It's NOT subject to Samsung's recall.

Apparently, the most common cause of leaks is the water drain pump, located in the left rear.

I haven't diagnosed the leak. What should I do, should I decide to engage is this adventure?

A new OEM water pump costs only about $19 on Amazon, but the DIY video to replace it is about 17 minutes long vs. Whirlpool-made top loader water pump videos of less than 5 minutes, meaning it will probably take me a couple of hours to do.

I'm awaiting deliver of a new top-loader, but the top loader won't be able to handle comforters and blankets.

I have basement space to keep the Samsung and craigslist prices for similar washers are abysmal.

If I do only occasional loads (once every few months of comforters and blankets), do I really need to change the water drain pump? What's the worse that will happen?

If I change the water pump, how likely is this to recur, ie how long do Samsung water pumps last?

Thanks

via Samsung Front Loader Leaking - Worth Repairing?
by giants1

LSQ9550PW3 Whirlpool Top Loading Washer Leaking

Made in 2005.

Washer has not been used for one month. Has musty smell in tub ("porcelain in steel basket" per underside of lid), but no visible rust in tub. Wiped with vinegar and left lid open.

Reportedly, it had an undetected leak from the right rear for one month which damaged the floor.

Padding on right front is wet, but nowhere else.

Drain pump: dry exterior no foreign bodies inside; gears move easily; no leaks. Removed drain pump easily and filled with water over sink; no leak. Motor spline that connects to drain pump without rust.

Drain pump hoses: clamps intact; dry; no leaks

Filled tub with water, power off; no leaks observed

Water inlet mixing valves both have continuity; solenoids without blemish; valve screens clear

What do I do next?

Also, the lid switch is on the underside of the cabinet, so I can't stick a screwdriver in it to keep the lid open and observe filling. How do I jump the lid switch?

Thanks!

via LSQ9550PW3 Whirlpool Top Loading Washer Leaking
by giants1

Whirlpool Top Loading Washer Leaking

Made in 2005.

Washer has not been used for one month. Has musty smell in tub ("porcelain in steel basket" per underside of lid), but no visible rust in tub. Wiped with vinegar and left lid open.

Reportedly, it had an undetected leak from the right rear for one month which damaged the floor.

Padding on right front is wet, but nowhere else.

Drain pump: dry exterior no foreign bodies inside; gears move easily; no leaks. Removed drain pump easily and filled with water over sink; no leak. Motor spline that connects to drain pump without rust.

Drain pump hoses: clamps intact; dry; no leaks

Filled tub with water, power off; no leaks observed

Water inlet mixing valves both have continuity; solenoids without blemish; valve screens clear

What do I do next?

Also, the lid switch is on the underside of the cabinet, so I can't stick a screwdriver in it to keep the lid open and observe filling. How do I jump the lid switch?

Thanks!

via Whirlpool Top Loading Washer Leaking
by giants1

Frigidaire Affinity front load washer won't final spin

Washer won't final spin. Have seen many submissions on this. When I run it in diagnostic mode, it will spin full bore. The tech sheet says replace latch assembly. I did. Still the same. Should I assume that I got a bad door latch assembly? Perhaps the door strike is bad? Or something else? Thanks a ton.

via Frigidaire Affinity front load washer won't final spin
by dcowell17

Tired of Scamsung washers, need recommendations for one without SPIDER ARMATURE issues

Hello everyone! First post here. I am driven here by my outrage with Samsung washers. But apparently it's not unique to Samsung.

Its a long story of how I ended up with two different makes of Samsung front loading HE washers, but irrelevant. Both have issues with balance, due to the armature corroding. I'm sick of it. It's absolutely mind numbingly inexcusable, if not criminal the way they have promoted these washers over the years with bullet points about the stainless steel drum, long warranty on the drum, direct drive motor, etc. And then to put these sky high price tags on them. The drum will never corrode! It's stainless steel! Hooray! What we aren't telling you, is that what is behind the drum cannot, will not, stand up to chemicals! It will start falling apart, clogging up and ruining your drain pump, stinking up your clothes with crevices and nooks and crannies that hold all sorts of residue. As it falls apart, it will get more and more out of balance, your clothes will take longer to wash, the little shock things will not be able to handle the balance issues, etc. The replacement parts are expensive, and if you aren't doing it yourself, it's financially impractical to have it serviced! I've put 15 years on the "old style" top loader with the agitator in the center, and paid $200-$300 for those, and yet these "HE" front loaders are routinely $800+ and fall apart after a few years. It's criminal.

So I am asking for your advice. Thanks in advance. I really need to go get a new washer this weekend. I have two that I am going to get rid of. I am sick of the problems.

Are ANY high efficiency washers free of this corroding armature and the associated balance problem?
Or do I need to go back to the old style washer?

via Tired of Scamsung washers, need recommendations for one without SPIDER ARMATURE issues
by clives

Loud Noise

The machine function's correctly until I started a load with two large bath towels and three small kitchen towels. It made through the wash cycle and when it got to rinse it started to make a loud intermittent noise like whaaaaaaaaaaaaaa - whaaaaaaaaaaaaaaa-, etc. Can some help identify the problem.

via Loud Noise
by billsh

OE error on Kenmore Elite Front loading Washer... will tumble but not spin.

Kenmore Elite front-loading washer was getting an OE error code. Changed Drain pump motor and verified no blockages. Started washer and same result. Found and performed a diagnostic test mode procedure, and found all diagnostic tests good except for the "low speed spin" and "high speed spin" tests.

Washer will tumble in both the clockwise and counterclockwise directions (tests #1 and #8) but will not spin (tests #2 and #3). When entering into test #2 (low speed spin) and #3(high speed spin), the drain pump engages and you can hear water draining the drain hose into the house drain, but without the spin cycle engaging the clothes are WET!

Any ideas why it will tumble but not engage to the higher speeds for the spin cycles?

via OE error on Kenmore Elite Front loading Washer... will tumble but not spin.
by Troubledagain

WT1501CW Problems with leaking?

I'm part of a washer replacement program with my energy company. My washer is 21 years old so the energy company will swap it out with a new machine for free. The two available machines are the front loading Whirlpool or a top loading LG. The space is too small for the Whirlpool (the front door has a really bulgy rim around it) but I was warned that the top loading LG has had problems with leaking.

Does anyone know if this is true? Does the LG WT1501CW leak? Why does it leak? Should I not select this machine? How difficult is it to fix?

If I take the Whirlpool I would have to modify my laundry space with some construction.

via WT1501CW Problems with leaking?
by Jezjax

Problems with leaking?

I'm part of a washer replacement program with my energy company. My washer is 21 years old so the energy company will swap it out with a new machine for free. The two available machines are the front loading Whirlpool or a top loading LG. The space is too small for the Whirlpool (the front door has a really bulgy rim around it) but I was warned that the top loading LG has had problems with leaking.

Does anyone know if this is true? Does the LG WT1501CW leak? Why does it leak? Should I not select this machine? How difficult is it to fix?

If I take the Whirlpool I would have to modify my laundry space with some construction.

via Problems with leaking?
by Jezjax

Washer intermittently not spinning

Hi - I suspect I may have a imminent component failure on my Kenmore 700 series washer.

About every 20 loads, the load will not spin out, although the agitator is fine and the water does drain. It is similar to the issue described in this thread, just far more intermittent.

Could this situation also occur if insufficient water amount is used for a load? I ask because it seems to happen on the Low and Low/Med water level settings.

Thoughts?

via Washer intermittently not spinning
by andyman1970

Just Bought Speed Queen Washer. Your Thoughts: Prev Maintenance and Tools?

Hi,

I have a 2012 Samsung front loading washer that's leaking from the left rear. This is consistent with the water drain pump and/or hoses going out. Sadly, the extended warranty just expired and I've been gentle with it.

Three days ago, I bought a Speed Queen. Delivery should be by the end of next week.

It's a top-loader with mechanical dials. Here's the model number:

AWN432SP113TW04

and a link to specs:

http://ift.tt/2kxuCLS

I'm willing to do preventive maintenance (eg clean lint screen and ducts), but I don't want the drama of an intermittent problem like I'm having with my Kenmore dryer..

I run about one load per week with some clothes very dirty due to working on my car and the house.

I live in an area prone to rust (eg hand tools rust quickly), but it's not cost-effective to run a dehumidifier. My current washer and dryer has some surface rust, probably due to dings/scratches (although my Samsung had a circular rust spot on top, so I must have set something obnoxious on there).

I'm the type of person who wants my appliances to last a long time, and I've been through a Maytag Neptune and a 4 year-old leaking Samsung front loader (not covered by the recall/class action lawsuit).

What are common problems with this model?

The leaking tub seal replacement repair is scary! Anything I can do to reduce the chance of having to do that repair?

The washer needs two special tools:

725P3 which is a kit including the hex nut wrench, spring hook, and two agitator hooks

294P4 or TJ294P4 (agitator drive bell puller) for Drive Bell 39508P

They're a bit pricey. Any inexpensive places to find them?

The drive bell looks like a generic 4" gear puller would work. Any thoughts on that?

How hard is it to get the agitator hex nut off?

Should I loosen it right after the warranty expires, then put anti-seize on the threads? Ditto with anti-seize on any other components?

Are there any other special tools I should have?

FYI, I posted a similar query in the dryer section for a Speed Queen gas dryer I'm planning on getting.What preventive maintenance do you recommend that I do under warranty that won't void the warranty?

Any suggestions about rust prevention?

After the 3 year warranty expires, what sort of additional preventive maintenance should I do?

Are there parts that I should have on hand and/or replace on a preventive basis, like some people do on their cars?

The motors are pricey. Have you rebuilt them or had a motor shop do that? If so, where do you find replacement bearings and carbon brushes?

Is the motor brush kit/assembly part number 927P3P used in this motor?

Ditto with transmissions. There is a pricey ($70) transmission rebuild kit, p/n RB150004, S/N9501 that contains two (silicone?) tubes 24 oz of transmission fluid, CW Trans F-94, 27243P for $22 and a rectangular block. I presume that synthetic car automatic transmission fluid and automotive gasket sealer would be more than adequate?

I suppose Youtube has videos on repairing Speed Queen dryers. Any ones in particular that I should study?

I bought it on my Visa, so I get an extra year extended warranty. They told me that if I have a problem during the extended warranty period, I can get any professional appliance repair person (eg independent shop), to provide a written diagnosis. Submit the diagnosis, warranty card, and receipt to them. Actually, I can submit the latter two on-line to make things easier. They'll reimburse me cash and I can either repair it myself, have a tech repair it, or buy a new unit.

I've never deal with a credit card extended warranty. Any suggestions for dealing with extended warranty service?

Thanks!

via Just Bought Speed Queen Washer. Your Thoughts: Prev Maintenance and Tools?
by giants1