Kenmore Elite Oasis HE leaking *photos*

Water is dripping off of the bottom of this part here, although I cannot tell where it is coming from. It will soak a bath towel in 2-3 loads. Ideas?

via Kenmore Elite Oasis HE leaking *photos*
by Sarahlorrain

WT5070CW LG top load washing machine leaking

Hi, does anyone know a solution to this? Can’t find out how to fix this problem. It is leaking in the weirdest spot. On the bottom but in the front of the machine so it’s not coming from any hose. Hopefully the video I attached works. Thanks!

via WT5070CW LG top load washing machine leaking
by Pisano772

AWN432SP113TW04

My SQ washer is dripping water into the tub 24/7. I've researched and assume it's the fill valve/water inlet valve, but I'm having trouble finding the part #. Also, anyone have any good videos on how to replace? I see videos showing Maytag replacement from the control panel, but my SQ has the valve on the back with its own access panel.

Thanks in advance to people doing great work on this forum!

via AWN432SP113TW04
by mjbr24

Kenmore 700 Series smells like something is burning.

Good Afternoon,

I am wondering if anyone can help. My Kenmore 700 Series Model 110.28132410 smells like something is burning. Hear sparking noises and it will not run any cycle.
It just started today. I took a pic of the bottom. Not sure if its the motor and its burned or if that is dirt from the bottom.

via Kenmore 700 Series smells like something is burning.
by Kdiggy

GE WJRE5550H1WW Clothes still wet after spin

Hello all. Towels/wash rags still wet at the end of the rinse/spin cycle. Doesn't seem to be a problem with other clothes. I could find no blockages in washer drain system. Drain pump had a bit of end play in impeller and being 14 years old I replaced the pump. I watched a complete cycle and everything seems to be fine except: during the spin cycles the drain pump only ran for a short time at the beginning and again at the end of the spin cycle. Seemed to drain fine after wash cycle. Only...

Read more

via GE WJRE5550H1WW Clothes still wet after spin
by hoot

Speed Queen AWN542SP111TW01 loud during spin

Out of the blue today, my washer started making a very loud noise during the spin cycle. Gets louder the faster it spins.

via Speed Queen AWN542SP111TW01 loud during spin
by Hthrkln

CTW41N1AW Criterion Washer - Adhesive on water pump. Do I need it?

The water pump on my Criterion CTW41N1AW (I think it is made by Whirlpool) clothes washer died. I have a new one coming today but wanted to ask a question. When I took the old original one off along with the bolts that part had no gasket that I could see and it looked like it was sealed on with a yellow adhesive. The new part I purchased to replace it looks like it is the same one but the new one has a black gasket like material where it joins the tub. They also had it smeared on the...

Read more

via CTW41N1AW Criterion Washer - Adhesive on water pump. Do I need it?
by maestroc

W11330506A/W11330507ASP Whirlpool washer turned on by itself

Hello,
My washer turned on by itself in the middle of the night. I unplugged it and now it stopped turning on by itself.
But when turning it on, it makes noises on its own as if it started a cycle, but no water comes in and it doesn't spin.
All buttons except the START button work. There is no error symbol/code that appears.

I tried resetting it by pressing the POWER button for 3 sec as suggested by the manual, but it only turned off the washer.
Unplugging, waiting for a few minutes...

Read more

via W11330506A/W11330507ASP Whirlpool washer turned on by itself
by muriel27

Washing Agitation squeak, with load

Good morning,
I have had a repair company try to fix my brand new Maytag washer with no luck, looking for help.
When the washer has a load, whether clothes or just water, in agitation mode it squeaks, every time it moves, no squeak happens when in test mode and there is not weight in the drum.
Parts replaced are the gear pulley, along with the actuator that moves the gear up and down.

Any help will be greatly appreciated.

via Washing Agitation squeak, with load
by Cratoppel

Whirlpool Cabrio Wont spin

Hoping you experts can help me fix the no spin issue with my whirpool cabrio top load washer.

Initially, the washer was very loud during the spin cycle, so I replaced the bearings, shaft, and seal with oem parts. While doing this, I messed up the RPS, so I replaced that with the entire kit that included the wiring harness.

Now the washer will not spin on its own.
I can spin the tub by hand very easily.

When in diagnostic mode, I get F82, F41, F51, and F50.
While in manual diagnostic...

Read more

via Whirlpool Cabrio Wont spin
by aj10203

Washers pump keep blowing up

I have an old Inglis top loading washer (maybe 15 years old) and a few months ago the pump stopped working. Everything else was working fine, but when it got to the pump cycle it just wouldnt do anything. So I replaced it with a similar Inglis washer (model #IA4200) that I had on the side, maybe a few years older. Now that one is doing the exact same thing. It washes and spins and everything, but it will not pump. I still have the first one and can confirm that the pump itself is not...

Read more

via Washers pump keep blowing up
by steff_ff3

Popping / clicking sound in Kenmore HE3 washing machine

I have an abnormal sound in a Kenmore Elite HE3 front loading washing machine. The washer is functioning with zero problems. The clothes get very clean, it's just a bit annoying if I leave the laundry room door open.

It appears to be correlated to the rotation angle of the tub. It is not a normal loud bearing sound. I replaced the bearing about two years ago and it's been working great but now has this popping sound that increases in frequency as the tub spins faster. I can manually...

Read more

via Popping / clicking sound in Kenmore HE3 washing machine
by Jcoder

Maytag Board

I have this Maytag washer that just started to act up. I tried to put it in a diagnostic mode and it won't do it. Then I noticed when you try to spin the dial to any cycle the light on the dial stays where ever it started from when you powered it on. I'm thinking it's the board because it won't go into diagnostic mode in the first place. I would like to get a better idea on what's causing it before I replace a expensive board.

via Maytag Board
by tseibring

MVWX500BW0 makes noise and does spin but cloths still wet

Please help. I have the MAYTAG MVWX500BW0 washer and I have these issues:

1.) Making noise when spinning (maybe bearing worn out?)
2.) When doing full or medium load it leaks water under the washer.
3.) After spinning the cloths are still wet, but it seems like pump is working but making lots of noise. I have to unplug the washer from power, wait 1-2 min then plug it back and put it on drain and spin mode and then the cloths are less wet after it finishes the cycle.

Spining Noise...

Read more

via MVWX500BW0 makes noise and does spin but cloths still wet
by dusand