Hotpoint washer has no spin cycle

Have a Hotpoint washer MOD # VBSR3100DAWW -it will run as normal except it won't spin after the rinse cycle and lower area of washer seems to have a slight hum and if left your can smell electrical smell .I'm assuming motor trying to turn??

I have checked pressure switch NC+COMMON has continuity, and opens on meter when you blow into pressure tube, NO+ common shows open and closes when you apply air to pressure switch tube and tube is clear as well as pressure bell.

Have metered the...

Hotpoint washer has no spin cycle

via Hotpoint washer has no spin cycle
by hotpoint john

Bosch wan 28201- lock won't go down, can't close door

Hello,

I recently bought this washing machine. I had to take the door off to fit it into the utility room but when I put it back on the lock (latch?) was up and I couldn't shut the door.

I called the supplier but they refused to take it back as I had taken the door off and I can't get hold of the local engineer they gave us a number to get it fixed.

I tried the release at the bottom of the machine but this isn't working either.

I have two children under 2 so the washing is really piling...

Bosch wan 28201- lock won't go down, can't close door

via Bosch wan 28201- lock won't go down, can't close door
by plloyd88

Whirlpool Bravos MCT washer Clothes Still Wet

What I have tried;

1. I have removed Change from under the agitator.
2. I have replace the drive belt.
3. I have check the pump and all hoses for obstructions.

The water seems to flow quite freely from the machine. However, I now notice that the machine does not spin nearly as fast a it used to. Also, there is a Fluttering sound when it starts to spin. I have a video attached.. Any help would be appreciated.

via Whirlpool Bravos MCT washer Clothes Still Wet
by jbnlwilliams

LG Washer overfilling

I’m working on a LG washer about 12 years old, no water was coming out so I changed the inlet valves, now it’s overfilling. I changed the water level sensor switch and no luck. So I put the old inlet valves back and no water coming out, so yes that was bad. Put the new inlet valves again and again overfilling; for sure I thought that inlet valve was bad also, so I went bought another one and same thing, overfilling. I pin pointed which one was overfilling and it was the cold one for the wash...

LG Washer overfilling

via LG Washer overfilling
by Sem

Whirlpool WFW95HEDW0 Error F03 E01

Hi, I’ve searched the forums for the error codes F03 E01 and I saw that it was recommended to change the air trap and the pressure switch. I’ve replaced both of them and it is still giving that error. I’ve removed the drain and there is nothing in the trap plugging it up. It sounds like there is water in the tub but it will not drain. I’ve tried running the drain and rinse cycle and it will hit that error while it’s sensing. Any cycle I try running will give the error while it’s sensing but...

Whirlpool WFW95HEDW0 Error F03 E01

via Whirlpool WFW95HEDW0 Error F03 E01
by JenJones

Washer Spins but Pump does not always kick in to drain?

Have an old Kenmore 417.99812990. It has been leaking intermittently for some time, today i noticed it went into spin cycle but pump did not kick in to drain so the washer spun the water out. (fool me once, i have water alarms to let me know immediately when this happens) That said, i changed it to "extra rinse" cycle and it began to spin and then the pump kicked in to drain. Could it be the switch or the control board? Thanks in advance for the input.

via Washer Spins but Pump does not always kick in to drain?
by sarcoidboy

Whirlpool Cabrio WTW8100BWO

My Cabrio Washer when off is leaking drops of water into the drum through a clear plastic unit that the water lines seem to be connected to. Any idea why it’s leaking? Unit is about 5 years old.
thanks
Larry

via Whirlpool Cabrio WTW8100BWO
by Larry Rose

WFMC3301UC-09 Bosch Nexxt 500 won't spin. Pump or control module?

I'm getting an error E:04 when completing a rinse and I don't get any spin post rinse. Most of the water drains except for the last bit then the pump just runs and runs but no spin then error out. I cleaned the pump cleanout really well and ran washer cleaner affresh 5 times now. The pump seems to work (not any weird noise and it pumps out lots of water after the wash cycle and on rinse before the error) but still no spin. Manual says if not all the water is drained it won't start...

WFMC3301UC-09 Bosch Nexxt 500 won't spin. Pump or control module?

via WFMC3301UC-09 Bosch Nexxt 500 won't spin. Pump or control module?
by Matildar2662

Maytag Bravos mvwb850wl2 still very noisy after bearing replacement

Model Number: Maytag Bravos mvwb850wl2
Brand: Maytag
Age: 6-10 years

Hi!

2 weeks ago I replaced my washer machine bearings. I tested it with a heavy load and it looked perfect. I ask my wife a couple of time since then and she said it looked okay.

But, today, I heard that same (or very similar) very noisy sounds when spinning at high speed. Inside the washer was many bed sheets so it was a heavy load. When I replaced the bearings I saw that rotor internal spline/gear were pretty used...

Maytag Bravos mvwb850wl2 still very noisy after bearing replacement

via Maytag Bravos mvwb850wl2 still very noisy after bearing replacement
by JPGraphX

Bosch Nexxt 500 won't spin. Pump or control module?

I'm getting an error E:04 when completing a rinse and I don't get any spin post rinse. Most of the water drains except for the last bit then the pump just runs and runs but no spin then error out. I cleaned the pump cleanout really well and ran washer cleaner affresh 5 times now. The pump seems to work (not any weird noise and it pumps out lots of water after the wash cycle and on rinse before the error) but still no spin. Manual says if not all the water is drained it won't start...

Bosch Nexxt 500 won't spin. Pump or control module?

via Bosch Nexxt 500 won't spin. Pump or control module?
by Matildar2662

Not completing spin cycle/continuous cycle running

Maytag Bravos washer. The washer is not completing the spin cycle and then moves to done. The washplate appeared to be “ spinning out” faster than the drum and had bad grinding noise. Took apart washer , cleaned out some change, cleaned out gunk. Put everything back together, ran calibration. The calibration went accordingly. The grinding stopped but the spin cycle/ rinse repeat still happening. Tried again. Found clothes come out wet. It spins some , drains , then start a rinse cycle...

Not completing spin cycle/continuous cycle running

via Not completing spin cycle/continuous cycle running
by Cbwork

522701-W0 beaumark washer on spacesaver 27 drive belt doesn't fit

522701-W0 beaumark washer on spacesaver 27 drive belt doesn't fit

It will not fit around the idler arm no matter which way I move it. I have pictures I f anyone needs them, really need help here.

via 522701-W0 beaumark washer on spacesaver 27 drive belt doesn't fit
by Ryankubb