Speed queen model awn43rsn115tw01motor bearings replacement

The motor on my speed queen model awn43rsn115tw01 are noisy. I realize that the motor is not designed to be taken apart. What I would like to know is the pulley on the motor threaded and if so left or right.

The motor is a three phase with an inverter

via Speed queen model awn43rsn115tw01motor bearings replacement
by Clydesteve

Samsung Washer Flange Shaft Replacement

Flange Shaft corroded and broke below drum. Ordered 3 different parts with Samsung number. Fits bolt pattern on drum but won't fit shaft. Is this a common problem. Been through 3 different parts companies and backorder. Does anyone have information or a fix?

via Samsung Washer Flange Shaft Replacement
by jnall2

110.92480200 How to take agitator apart to replace Dog Agits?

The Dog Agits part #8800400 on my Kenmore Washer 110.92480200 broke. All the videos I've seen on replacing them (such as this one:

) say to remove the bolt in the middle of the agitator, then the top part of the agitator just pops out.

We took the entire agitator out to replace the lint filter underneath the basket (we removed the entire basket). The agitator came out in one piece. How do we get it apart so we can replace the dog agits? This agitator does not have a...

Read more

via 110.92480200 How to take agitator apart to replace Dog Agits?
by Lizzy

Whirpool HE Top-Load washer WTW5100HW0 F7E1 error

I was able to find online that this error leads to possibly replacing the shift actuator. Ordered and replaced the part, but am still receiving the error code *sometimes*. I've run "drain and spin" cycles, and a "quick" cycle with the washer empty. Previously, the "drain and spin" cycle would look like its going to start, click and hum a few times, then go right to 1 minute left, drain, and ping "washing complete" as if it had gone through everything correctly (but show no error). After...

Read more

via Whirpool HE Top-Load washer WTW5100HW0 F7E1 error
by kwill624

AWN432SP111TW01 Speed Queen washer dead

Speed Queen top load washer quit mid cycle, after fill and wash, start of drain and rinse
Unplugged and restart… dead
Wont respond to any controls, will not fill with more water with change/reset of fill dial, will not agitate, will not spin, will not drain
Checked lid lock switch and ok on ohm meter
Motor spins freely, belt fine
Swapped out mechanical timer (main dial)… still dead

Any suggestions?

Thanks,
Michael

via AWN432SP111TW01 Speed Queen washer dead
by Azmcarroll

Maytag Bravos XL Washer (Code LD - Long Drain)

Maytag Bravos XL Washer (Code LD - Long Drain)

MOD. MVWB850YW0
SER. C13572628
TYPE: 580-05

FYI: Sears Service Warranty completely rebuilt the entire machine... bearings, pumps, electronics, etc.!
Drain Pump motor is humming/spinning (also hearing a "clattering" noise), but not draining. Unplugged power & Turned off water valves!
Removed back cover. Drained remaining water in tub into bucket by lowering hose below tub level.
Tilted machine forward, then used auto jack stand to hold up...

Read more

via Maytag Bravos XL Washer (Code LD - Long Drain)
by Sevysuite

GE top load washer - replaced shaft tube, new shaft squeeks. Normal?

I have a GE top load washer that was sounding like a jet taking off on the spin cycle. Reading here lead me to replace the shaft tube and the tub bearing while I was at it. After installing the new tube it squeaks a lot. The squeak is coming from the bearing in the new shaft not the tub bearing or the belt.

Is this a bad bearing/shaft? Will the squeak fade as it "breaks in"? Can I try lubricating it?

via GE top load washer - replaced shaft tube, new shaft squeeks. Normal?
by Tim K